Nov 03, 2026 Leave a message

Cu-Ni 90/10 (UNS C70600) Reducers

What Is a Cu-Ni 90/10 Reducer?

A reducer is a pipe fitting used to connect two pipes with different nominal diameters. It provides a gradual transition between a larger pipe and a smaller pipe, allowing the piping system to accommodate changes in pipe size.

A Cu-Ni 90/10 reducer is manufactured from 90/10 copper-nickel alloy and is used where the piping design requires the corrosion resistance and other properties of this material.

 

For example, a DN125 × DN65 reducer connects a DN125 pipe to a DN65 pipe. The fitting provides a transition between the two pipe sizes while maintaining the specified material and wall thickness requirements.

 

Cu-Ni 90/10 (UNS C70600) Material Characteristics

Cu-Ni 90/10 is a copper-nickel alloy containing approximately 90% copper and 10% nickel, with controlled additions of iron and manganese.Its commonly used UNS designation is C70600.

The addition of nickel, iron and manganese gives this alloy useful properties for marine and industrial water systems, particularly where seawater corrosion resistance and reliable piping performance are required.

 

Chemical Composition of UNS C70600

When purchasing C70600 reducers, buyers should check the chemical composition against the specified material standard.

The following table gives the typical ASTM C70600 composition limits for reference.

Element Chemical Composition (%)
Copper (Cu) Remainder
Nickel (Ni) 9.0–11.0
Iron (Fe) 1.0–1.8
Manganese (Mn) 1.0 max.
Lead (Pb) 0.05 max.
Zinc (Zn) 1.0 max.

Note: These limits are reference values for C70600 under the relevant ASTM material specifications. The applicable product standard and any purchaser-specified restrictions should be checked before ordering.

 

Why Is Cu-Ni 90/10 Used in Marine Piping?

Seawater Corrosion Resistance

Cu-Ni 90/10 has good resistance to seawater corrosion under suitable operating conditions. Its protective surface film helps reduce corrosion during service in marine environments.

 

Resistance to Biofouling

Copper-nickel alloys can help limit marine organism attachment compared with many other piping materials. This is useful in seawater intake and circulation systems.

 

Erosion-Corrosion Resistance

The alloy offers useful resistance to erosion-corrosion in properly designed seawater piping systems. However, fluid velocity, turbulence, suspended particles and operating conditions must still be considered.

 

Weldability and Fabrication

Cu-Ni 90/10 can be fabricated and welded using suitable procedures. Material condition, joint preparation, filler metal and welding procedures all affect the final connection quality.

 

These characteristics make C70600 a commonly selected material for marine piping components, including pipes, tubes, fittings and flanges.

 

Need Cu-Ni 90/10 or UNS C70600 materials for your project?

Send us your required material grade, product type and dimensions. Our team can review your specifications and discuss the available supply options.

 

Types of Cu-Ni 90/10 Reducers

Before ordering copper-nickel reducers, buyers should identify the required fitting configuration. The two main configurations are concentric and eccentric reducers.

Concentric Reducer

Concentric Reducer

A concentric reducer has a symmetrical tapered body, with both ends sharing the same centerline.

 

Its main characteristics include:

Both ends are centrally aligned.

The diameter changes gradually along the fitting.

It is suitable for piping arrangements with aligned centerlines.

It is commonly used in vertical piping sections and other suitable pipe layouts.

 

When specifying a concentric reducer, buyers should confirm the large-end diameter, small-end diameter, overall length and wall thickness.

 

Eccentric Reducer

An eccentric reducer has an offset structure, with one side of the fitting remaining flat.

 

Its main characteristics include:

The centerlines of the two ends are offset.

One side can be aligned with the required pipe elevation.

It is commonly considered in horizontal piping layouts.

Its orientation needs to be specified during installation planning.

 

For example, in certain horizontal pump suction arrangements, an eccentric reducer may be used with its flat side positioned to help avoid air pockets. The correct orientation depends on the piping design.

 

The difference is not simply appearance: the two configurations affect pipe alignment, elevation and installation arrangements.

 

Seamless vs. Butt Weld Cu-Ni 90/10 Reducers

Seamless Reducer

A seamless reducer has no longitudinal weld seam in the reducer body. Its body is produced from seamless material through suitable forming and machining processes.

No longitudinal weld seam along the fitting body.

The reducer body is formed from seamless starting material.

The finished fitting still requires dimensional and wall-thickness inspection.

Suitable when the project specification explicitly requires a seamless fitting body.

 

Seamless Reducer

Seamless Reducer

 

Welded Reducer

A welded reducer has one or more welded seams in its fitting body, depending on its manufacturing construction. The body is made by forming and joining material rather than producing the entire body from seamless starting material.

A weld seam is present in the fitting body.

Weld quality and inspection requirements become part of the purchasing specification.

Buyers should confirm the permitted welding process and required weld examination.

It should not be supplied as a seamless fitting when the project requires a seamless body.

 

Welded Reducer

Welded Reducer

 

Comparison

Seamless Reducer

Welded Reducer

Body construction

Manufactured without a longitudinal body weld seam

Manufactured by forming and welding material

Weld seam

No longitudinal manufacturing seam in the body

One or more manufacturing weld seams may be present

Inspection focus

Dimensions, wall thickness, material properties and surface condition

The same checks, plus weld quality and specified weld examination

Manufacturing

Requires suitable seamless starting material and forming capability

Uses formed material and welding processes

Cost

Can be more expensive, depending on size and availability

May be more economical for certain large sizes or constructions

Supply considerations

Limited by available seamless material sizes and forming capacity

Depends on plate or sheet availability, welding process and inspection requirements

 

When Should You Choose a Seamless Reducer?

The project specification explicitly requires seamless fittings. This is the first condition to check; do not substitute welded products without approval.

The buyer wants to avoid a longitudinal manufacturing weld seam in the fitting body.

The project has specific requirements for body construction and weld-related inspection.

The required size and wall thickness are available through a suitable seamless manufacturing route.

 

When Can You Choose a Welded Reducer?

The project specification permits welded construction.

The required reducer size or wall thickness is difficult to produce economically from seamless material.

The manufacturer can provide the required welding procedure, weld inspection and material traceability documents.

The buyer wants to compare the total cost and delivery time of welded and seamless options.

Email Us Your Requirements

 

Specifications and Dimensions of C70600 Reducers

Correct dimensional information is essential when ordering Cu-Ni 90/10 reducers. A fitting may have the correct material grade but still be unsuitable if its end dimensions, wall thickness or overall length do not match the piping design.

 

Common Reducer Size Combinations

Copper-nickel reducers can be supplied in different diameter combinations according to project requirements.

The following examples illustrate common size descriptions:

Reducer Size Large End Small End
DN125 × DN65 DN125 DN65
DN125 × DN100 DN125 DN100
DN25 × DN20 DN25 DN20
DN25 × DN15 DN25 DN15
DN40 × DN25 DN40 DN25
DN40 × DN15 DN40 DN15

DN means nominal diameter, not the actual measured outside diameter.

For this reason, buyers should identify the applicable pipe dimensional standard and confirm the actual outside diameter and connection dimensions before ordering.

 

Wall Thickness Requirements

Wall thickness is one of the most important parameters in a reducer specification.

For example, a purchasing specification may require:

Example Size Minimum Wall Thickness
DN125 × DN65 3.2 mm
DN125 × DN100 3.2 mm
DN25 × DN20 1.8 mm
DN25 × DN15 1.8 mm
DN40 × DN25 2.1 mm
DN40 × DN15 2.1 mm

These are examples from a particular purchasing specification, not universal standard wall thicknesses for these sizes.

 

When reviewing a minimum wall thickness requirement, buyers should consider the following:

1. Minimum vs. Nominal Thickness

A minimum thickness requirement is different from a nominal thickness. The purchasing document should clarify whether the stated value applies to the finished reducer or the starting material.

2. Wall Thickness After Forming

During forming, material can redistribute and local thinning may occur. Therefore, the final fitting should be checked against the specified minimum thickness.

3. Thickness Measurement Locations

For reducers, it is useful to identify the inspection locations, including the large end, small end and transition section, according to the applicable inspection plan.

4. Manufacturing Tolerances

The acceptable dimensional and thickness tolerances should be agreed upon before production.

 

Dimensions to Confirm Before Ordering

In addition to nominal pipe sizes and wall thickness, buyers should confirm:

Parameter Description
Reducer Type Concentric or eccentric
Large End Nominal size and actual outside diameter
Small End Nominal size and actual outside diameter
Wall Thickness Minimum or specified nominal thickness
Overall Length Required fitting length
End Preparation Butt-weld end preparation or other specified connection
Manufacturing Method Seamless or butt weld
Material UNS C70600
Standard Applicable material and dimensional requirements

 

Dimensional and Wall Thickness Inspection of Copper Nickel Reducers

Dimensional and Wall Thickness Inspection of Copper Nickel Reducers

 

Applications of Cu-Ni 90/10 Reducers

Application Typical Piping Service Role of Reducers
Marine Seawater Systems Seawater intake and circulation Connect pipes of different diameters
Firemain Systems Firefighting water distribution Match pipe sizes between different system sections
Washdown Systems Deck and equipment cleaning water Connect branch lines and equipment connections
Fresh Water Generation Freshwater production equipment piping Connect equipment outlets and piping sections
Domestic Water Systems Shipboard domestic water distribution Accommodate changes in pipe diameter
Industrial Water Systems Water circulation and process piping Connect different pipe sizes in industrial installations

 

What Should Buyers Consider?

For each application, buyers should confirm:

Fluid type and operating temperature.

Design pressure and flow conditions.

Required material grade.

Reducer dimensions and wall thickness.

Applicable piping and project standards.

Copper Nickel Piping in Marine Seawater

Copper Nickel Piping in Marine Seawater

 

How to Specify and Purchase Cu-Ni 90/10 Reducers

Item Information to Provide
Material Grade Cu-Ni 90/10 / UNS C70600
Reducer Type Concentric / Eccentric
Large End Size DN or actual outside diameter
Small End Size DN or actual outside diameter
Wall Thickness Minimum or nominal thickness
Manufacturing Method Seamless / Butt Weld
Overall Length Required dimension
End Preparation Butt-weld or other specified connection
Applicable Standard Material and dimensional standards
Quantity Required number of pieces
Certificate MTC / EN 10204 Type 3.1, if required
Delivery Destination Country and delivery location
Required Delivery Time Project schedule

 

FAQ

Q: Is UNS C70600 the same as Cu-Ni 90/10?

A: UNS C70600 is the commonly used designation for 90/10 copper-nickel alloy. However, buyers should always confirm the applicable product standard and chemical composition rather than relying on the alloy name alone.

Q: What is the difference between seamless and butt weld reducers?

A: A seamless reducer is formed from seamless starting material and has no longitudinal weld seam in its original body. A butt weld reducer is produced through a welded fabrication process. The appropriate choice depends on the project specification and piping design.

Q: Can Cu-Ni 90/10 reducers be supplied in custom sizes?

A: Yes, reducers can be specified according to project dimensions, subject to manufacturing capability and material availability. Buyers should provide the large-end size, small-end size, wall thickness, overall length and reducer configuration.

Q: How do I confirm the wall thickness of a copper-nickel reducer?

A: Wall thickness can be checked using suitable calibrated measuring instruments, including ultrasonic thickness gauges where appropriate. The inspection locations and acceptance criteria should be agreed upon according to the technical specification.

Q: What certificates are available for C70600 reducers?

A: The required documentation depends on the purchase order and applicable standard. Typical documents include a Manufacturer Test Certificate, chemical composition results, mechanical test results where required, and dimensional inspection records.

Request a Quote for Cu-Ni 90/10 Reducers

Choosing the correct copper-nickel reducer requires attention to material grade, fitting configuration, dimensions, wall thickness and manufacturing method.

Whether your project requires seamless C70600 reducers, butt weld reducers or custom copper-nickel fittings, the technical specifications should be reviewed before production and delivery.

We welcome inquiries from distributors, engineering contractors, shipbuilding companies and industrial project buyers.

 

To help us evaluate your requirements, please send:

Required material grade and standard.

Reducer sizes and wall thickness.

Seamless or butt weld manufacturing requirement.

Technical drawings, if available.

Required quantity and delivery destination.

Certificate and inspection requirements.

 

Send your inquiry or technical drawings to our team for a quotation and supply review.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry