ASTM B111 ASME SB 111 C44300 Admiralty Brass is ideal for heat exchanger tubes. Normally made to order to meet engineering requirements, you will find this alloy often times used in oil and gas applications that also require its non corrosive properties. C44300 and C68700 have good corrosion resistance. C44300 Admiralty Brass Seamless Tubes Tensile strength minimum in 310Mpa, Yield Strength minimum in 105Mpa.
ASTM B111 / ASME SB 111 C44300 Admiralty Brass Physical Properties
| Copper or Copper Alloy UNS No. | Melting Point | Density | Coefficients of Linear Thermal Expansion | Specific Heat Capacity | Thermal Conductivity | |||||
| °C | °F | lb/in3 | g/cm3 | 1×10-6/°C @ 20.0 – 30.0 °C | 1×10-6/°F @ 70.0 – 570 °F | cal/g-°C, 20 °C | BTU/lb-°F @ 70°F | W/m-K, 20 °C | BTU/ft2/ft/h/°F @ 70°F | |
| C44300 | 2140 – 2260 | 2010-2100 | 0.308 | 8.53 | 16.2 | 9 | 0.09 | 0.09 | 29 | 17 |
Typical Application of ASTM B111 ASME SB 111 C44300 Admiralty Brass
1. Industrial: Evaporator Tubing, Heat Exchanger Tubing, Condenser Tube Plates, Distiller Tubes, Oil Well Pump Liner, Ferrules, Bourdon Tubes, Condenser Tubes
2. C44300 admiralty brass tubes and C70600,C71500 copper nickel tubes are widely used in "Industrial Steam Turbine Condensers"
3. Plumbing: Strainers
SB111 C44300 material has the following benefits:
Durability – The structure and chemical composition of an SB111 C44300 makes it durable. Its products can last up to 10 years, depending on where you are using it and the frequency of use.
Cost-effective – The overall value of installing, functioning and maintaining products of this material is relatively low. You, therefore, get quality by selecting this material to manufacture your products.
Versatile usage – You can manufacture different products using this material. For instance, you can make pipes and tubes for a variety of usage.
Test:
Pitting Tests
Intergranular Corrosion Test
Chemical Analysis
Hardness Test
Copper products that GNEE can provide
|
High quality 99.9% pure copper pipe / straight copper tube / copper alloy pipe |
|||
|
Standard |
ASTM,DIN,BS,CDA,JIS,GB |
||
|
Material |
T1,T2,C10100,C10200,C10300,C10400,C10500,C10700,C10800, |
||
|
Shape |
Round,Square,Rectangular,etc. |
||
|
Specifications |
Round:wall thickness:0.2mm~120mm,outside diameter:2mm~910mm
Square:wall thickness:0.2mm~120mm,size:2mm*2mm~1016mm*1016mm Rectangularwall thickness:0.2mm~120mm,size:2mm*4mm~1016mm*1219mm |
||
|
Length |
3m,5.8m, 6m, 11.8m, 12m, or as required. |
||
|
Hardness |
1/16 hard,1/8 hard,3/8 hard,1/4 hard,1/2hard,full hard,soft,etc |
||
|
Surface |
mill,polished,bright,oiled,hair line,brush,mirror,sand blast,or as required. |
||
|
Price term |
EXW, FOB, CFR, CIF, etc. |
||
|
Payment term |
T/T |
||
|
Package |
Export standard package: bundled wooden box, suit for all kinds of transport, |
||
|
Delivery time |
According to order quantity |
||
|
Export to |
Singapore,Indonesia,Ukraine,Korea,Thailand, Vietnam, Saudi Arabia, Brazil, Spain, |
||
|
Application |
Copper pipe is the first choice of residential housing water pipes, heating, cooling pipes |
||
|
Straight copper rod/copper round bar |
|||
|
Standard |
ASTM,DIN,BS,CDA,JIS,GB |
||
|
Material |
T1,T2,C10100,C10200,C10300,C10400,C10500,C10700,C10800, |
||
|
Shape |
Round,Square,Rectangular,etc. |
||
|
Specifications |
Diameter:3~200mm |
||
|
Length |
3m,5.8m, 6m, 11.8m, 12m, or as required. |
||
|
Hardness |
1/16 hard,1/8 hard,3/8 hard,1/4 hard,1/2hard,full hard,soft,etc |
||
|
Surface |
mill,polished,bright,oiled,hair line,brush,mirror,sand blast,or as required. |
||
|
Price term |
EXW, FOB, CFR, CIF, etc. |
||
|
Payment term |
T/T |
||
|
Package |
Export standard package: bundled wooden box, suit for all kinds of transport, |
||
|
Delivery time |
According to order quantity |
||
|
Export to |
Singapore,Indonesia,Ukraine,Korea,Thailand, Vietnam, Saudi Arabia, Brazil, Spain, |
||
|
Application |
A copper rod is a type of colored metal processing bar stock with high electrical conductivity. It is mainly divided into brass |
||
|
Size |
Width: 10mm to 2000mm, |
||
|
Hardness |
1/16 hard,1/8 hard,3/8 hard,1/4 hard,1/2hard,full hard. |
||
|
Surface |
Polished,bright,oiled,hair line,brush,mirror,or as required |
||
|
Package |
Plastic film with Wooden case or wooden pallet |
||
|
Delivery time |
Prompt delivery or upon your order quantity. |
||
|
Quality Control |
Mill Test Certification is supplied with shipment,Third Part Inspection is acceptable. |
||
|
Application |
widely used inair conditioners,refrigerators,electric,solar water heater, polished pipe an be used in decorative,such as stair |
||
|
Shape |
Round, Square, Oval, can be customized |
||
|
Item |
Copper Wire |
||
|
Standard |
ASTM,DIN,BS,CDA,JIS,GB |
||
|
Material |
T1,T2,C10100,C10200,C10300,C10400,C10500,C10700,C10800, |
||
|
Shape |
Round |
||
|
Specifications |
As required. |
||
|
Length |
As required. |
||
|
Hardness |
1/16 hard,1/8 hard,3/8 hard,1/4 hard,1/2hard,full hard,soft,etc |
||
|
Surface |
mill,polished,bright,oiled,hair line,brush,mirror,sand blast,or as required. |
||
|
Price term |
EXW, FOB, CFR, CIF, etc. |
||
|
Payment term |
T/T |
||
|
Package |
Export standard package: bundled wooden box, suit for all kinds of transport, |
||
|
Delivery time |
According to order quantity |
||
|
Application |
Copper wire, as a conductive material, is widely used in power transmission and electronic devices. Transformers, inductors, |
||
Copper CNC machined parts
|
Custom CNC Machining Parts of Most Materials
|
||||
|
Quotation
|
According to your drawing(size, material, thickness, processing content, and required technology, etc)
|
|||
|
Materials Avaiable
|
Brass,Stainless Steel,Q235&Q345 steel, Zinc-plate Sheet,Stainless Steel, Aluminum,Copper, etc.
|
|||
|
Surface Treatment
|
Zinc Plating, chrome plate, powder coating, anodizing, wire drawing, silk-screen printing, etc
|
|||
|
Processing
|
Laser Cutting, Precision Stamping, CNC Bending, CNC Milling, CNC Turning, Threading, Riveting, Drilling, CNC Punching,Die Casting, Laser Welding, etc.
|
|||
|
Testing Equipment
|
CMM/Tool microscope/multi-joint arm/Automatic height gauge/Manual height gauge/Dial gauge/Roughness measurement
|
|||
|
Drawing Formats
|
PRO/E, Auto CAD, Solid Works , UG, CAD / CAM / CAE, PDF
|
|||
|
Our Advantages
|
1.) 24 hours online service & Quickly Quote/Delivery.
2.) 100% QC quality inspection before delivery, and can provide quality inspection form.
3.) 18+ years of experience in the CNC machining area and have a senior design team to offer perfect modification suggestions. |
|||
|
Tolerance丨Surface Roughness
|
Generally +/-0.1-0.2mm
|
|||
|
Sample service
|
Avaliable before bulk order. Samples charge according your design, The sample fee can be used as the payment for mass goods.
|
|||
About Us
Founded in 2008, we specialize in exporting premium copper products. Our manufacturing leverages continuous casting lines and precision drawing machines. Rigorous quality control, including eddy current testing and spectrometer analysis, guarantees the superior performance of our copper tubes and coils for global applications.
If you need any help, please contact us immediately!
Email address：sales@gneemetal.com
Square Meters Built
Enterprise Employees
Cooperating Partner
Years Experience
