C44300 (HSn70-1) admiralty brass pipe is the seamless copper alloy tube selected for the water side of shell-and-tube heat exchangers, surface condensers, feedwater heaters and refrigeration equipment. The alloy contains about 71 % copper with tin and a controlled arsenic addition, and it is the standard inhibited admiralty brass of ASTM B111/B111M and ASME SB111. HSn70-1 is the designation used in the Chinese national system for the same wrought composition. This guide covers the chemistry, mechanical requirements, size range, applicable standards and design considerations that decide whether C44300 pipe is the right choice for a given exchanger or condenser duty.
Alloy Identity and Where the Name Comes From
Admiralty brass takes its name from the naval service for which it was developed, and the C44300 composition is a continuation of that lineage: a copper-zinc alpha brass that was modified first with tin and then with arsenic to survive cooling water rather than to maximise strength. Tin raises resistance to flowing water and adds a small amount of solid solution strengthening. Arsenic is present at only a few hundredths of a percent and works as a cathodic inhibitor that stops the preferential removal of zinc from the alloy. Together these two additions turn an inexpensive 70/30 brass into a tube material that remains serviceable for decades in fresh, brackish and salt water circuits. In the Chinese system the same wrought alloy is written HSn70-1, where 70 indicates the nominal copper content and 1 the nominal tin content.
Chemical Composition
| Element | Range, % by weight | Nominal |
|---|---|---|
| Copper (Cu) | 70.0 - 73.0 | 71.0 |
| Tin (Sn) | 0.8 - 1.2 | 1.0 |
| Arsenic (As) | 0.02 - 0.06 | 0.04 |
| Lead (Pb) | 0.07 max | - |
| Iron (Fe) | 0.06 max | - |
| Zinc (Zn) | Remainder | 28.0 |
The arsenic and tin bands above are the ranges that define genuine admiralty brass tube. Chemistry submissions that quote copper at 89 - 91 % with 0.5 % nickel do not describe this alloy: that analysis belongs to a different copper-zinc system and would fail the C44300 limits of ASTM B111. Copper below 70 % reduces corrosion resistance, above 73 % the alloy drifts outside the composition that the standard permits, and arsenic outside the narrow 0.02 - 0.06 % window either fails to inhibit dezincification or embrittles the tube.
Mechanical Properties and Temper Selection
| Condition | Tensile strength | Elongation and use |
|---|---|---|
| Annealed, O61 | 310 MPa (45 ksi) typical minimum | High elongation, suitable for U-bends and roller expansion |
| Light drawn, H55 | 345 - 450 MPa typical | Moderate ductility, straight or gently bent runs |
| Drawn, H80 | 390 MPa or higher | Lower elongation, used where stiffness and erosion resistance dominate |
Tube is normally ordered in the softest condition that the fabrication sequence allows. U-bend exchangers work the outer fibre of the bend considerably, so annealed tube is preferred and bend radii are kept at or above the value used to qualify the bender. Where the bundle is rolled into a tube sheet, the annealed temper also gives the wall the plasticity needed for a reliable expansion joint. Only straight tube runs are normally supplied in a drawn temper. Strength and elongation are verified by tensile test on each lot, with the results reported against the requirements of the ordering specification rather than the figures quoted here.
Standards and Equivalent Designations
| System | Designation |
|---|---|
| UNS | C44300 |
| ASTM / ASME | ASTM B111/B111M, ASME SB111 |
| EN | CW706R, CuZn28Sn1As; tube ordered to EN 12451 or EN 12449 |
| DIN | 2.0470, CuZn28Sn1As |
| BS | CZ111 |
| JIS | C4430 |
| GB (China) | HSn70-1, seamless copper alloy tube for heat exchangers to GB/T 8890 |
A purchase order should state the tube standard, the temper, the outside diameter and wall thickness with tolerances, the length, the test requirements and the required marking. Eddy current testing, hydrostatic or pneumatic pressure testing and flattening or flaring tests are commonly called out in addition to the tensile test.
Size Range and Supply Forms
| Parameter | Range |
|---|---|
| Outside diameter | 2 - 914 mm |
| Wall thickness | 0.2 - 120 mm |
| Straight length | 4 m, 5.8 m, 6 m, or cut to order |
| Bent form | U-bend to tube sheet pitch |
| Surface | Mill, pickled, passivated or polished |
Condenser tubes are typically supplied in the small-diameter range with wall thickness chosen to give a corrosion allowance over the design life, while larger diameters and heavier walls serve process coolers, distillers and oil well pump liners. The same alloy is available as rod, plate, sheet, strip and wire so that tube sheets, baffles, ferrules and water boxes can be produced from a single metallurgy, which avoids galvanic mismatch inside the exchanger.
Design and Installation Considerations
Tube sheet joints: roller expansion, with or without grooves, is the standard method; the annealed temper gives a consistent expansion over the full sheet thickness.
Baffle spacing: keep the unsupported span short enough to control vibration, which is the most common cause of premature tube failure in condensers.
Water velocity: impingement and erosion-corrosion accelerate as velocity rises and as the water carries sand or suspended solids, so circuit velocity is set together with the tube alloy and cleaning strategy.
Water chemistry: sulphide, ammonia and heavy pollution reduce the life of admiralty brass and are the usual reasons for upgrading to a copper-nickel alloy.
Cleaning: mechanical brushing and chemical cleaning must both avoid scratching the protective film; deposits that blanket the tube promote under-deposit attack.
Typical Applications
Surface condensers for steam turbines and marine propulsion plant
Shell-and-tube heat exchangers and intercoolers
Feedwater heaters and evaporator tube bundles
Air conditioning and refrigeration condensers and chillers
Distiller tubes, ferrules and oil well pump liners
Frequently Asked Questions
Q: Is HSn70-1 the same alloy as C44300?
Yes. HSn70-1 is the Chinese designation for the wrought arsenical admiralty brass that the UNS system calls C44300, with nominally 70 % copper, 1 % tin and a controlled arsenic addition.
Q: What is the copper content of C44300?
The copper range is 70.0 - 73.0 % with tin at 0.8 - 1.2 % and arsenic at 0.02 - 0.06 %. Any analysis quoting copper near 90 % refers to a different alloy and does not meet ASTM B111 for C44300.
Q: Which temper should be ordered for U-bend tubes?
The annealed O61 temper, because bending works the outer wall of the tube and a soft temper reduces the risk of cracking during forming and during roller expansion into the tube sheet.
Q: What pressure and temperature can C44300 pipe withstand?
The allowable working pressure is calculated from the tube diameter, the wall thickness and the allowable stress of the alloy at design temperature under the applicable code. Thicker walls are selected where a corrosion allowance is required.
Q: Why does admiralty brass contain arsenic?
Arsenic at 0.02 - 0.06 % inhibits dezincification, the selective leaching of zinc that would otherwise attack plain brass in stagnant or low-oxygen cooling water.
Q: What tube sizes are available?
Outside diameters from 2 mm to 914 mm with wall thickness from 0.2 mm to 120 mm, supplied in 4 m, 5.8 m or 6 m straight lengths, as U-bends, or cut to the dimensions of the exchanger.




