Straight C23000 Tube for Condenser and Heat Exchanger Bundles
Condenser and heat exchanger bundles are built from straight tube lengths that must be dimensionally consistent from end to end, because the tube is expanded or rolled into a tubesheet at each end and supported by baffles along its length. C23000 red brass, an 85 % copper and 15 % zinc alloy, is supplied in straight random or fixed lengths for exactly this duty: the concentric wall expands evenly into the tubesheet, and the alloy resists the cooling water attack that governs bundle life.
The same straight tube stock is used well beyond condensers. Red brass is a general engineering material for pump cylinder liners, radiator cores, heat exchanger shells, flexible metal hose, instrumentation tubing and a wide range of architectural and hardware parts.
Chemical Composition
| Element | Cu | Pb | Zn | Fe |
|---|---|---|---|---|
| Weight % | 84.0 - 86.0 | 0.05 max | Remainder | 0.05 max |
Copper plus the sum of named elements must reach 99.8 % minimum, and single values in the specification represent maximums unless a range is shown. The high copper content relative to free-machining brasses is what maintains the single-phase structure and the resistance to selective leaching.
Physical Properties Used in Design
| Property | US customary | Metric |
|---|---|---|
| Density | 0.313 lb/in³ at 68 °F | 8.67 g/cm³ at 20 °C |
| Melting point, liquidus | 1830 °F | 999 °C |
| Melting point, solidus | 1770 °F | 966 °C |
| Electrical conductivity | 32 % IACS at 68 °F | 0.186 MS/m at 20 °C |
| Thermal conductivity | 81 Btu sq ft/ft hr °F at 68 °F | 140.3 W/m at 20 °C |
| Coefficient of thermal expansion | 10.6 × 10-6 per °F (68 - 572 °F) | 18.4 × 10-6 per °C (20 - 300 °C) |
| Modulus of elasticity in tension | 16000 ksi | approx. 110 GPa |
| Modulus of rigidity | 6000 ksi | approx. 41 GPa |
| Specific heat capacity | 0.09 Btu/lb °F at 68 °F | approx. 377 J/(kg.K) |
| Machinability rating (free-cutting copper = 100) | 30 | 30 |
Reliable conductivity, a moderate modulus and a low coefficient of thermal expansion are the values designers need when they compare red brass against other copper alloy tube grades for a given duty cycle.
Mechanical Property Range by Temper
| Temper | Tensile strength | Yield strength | Elongation |
|---|---|---|---|
| Annealed, O61 | 280 - 345 MPa | 95 - 150 MPa | 40 % min |
| Half hard, H02 | 380 - 430 MPa | 280 - 350 MPa | 20 % min |
| Hard, H04 | 450 - 520 MPa | 380 - 450 MPa | 8 - 15 % |
Straight tube for condenser service is commonly ordered in the annealed temper so that the wall expands into the tubesheet without cracking, while tube for liners and structural parts is supplied half hard or hard. Heat exchanger tube is specified to ASTM B111 or ASME SB111, which set the chemical, mechanical and dimensional acceptance criteria.
Fabrication and Heat Treatment Behaviour
| Technique | Suitability |
|---|---|
| Soldering | Excellent |
| Brazing | Excellent |
| Oxyacetylene welding | Good |
| Gas shielded arc welding | Good |
| Butt welding | Good |
| Spot welding | Fair |
| Coated metal arc welding | Not recommended |
| Seam welding | Not recommended |
| Capacity for being cold worked | Excellent |
| Capacity for being hot formed | Good |
Annealing is carried out in the range of roughly 425 - 730 °C according to the amount of cold work to be removed, and hot working is performed in the region of 790 - 900 °C. Both soldering and brazing are rated excellent, while welding processes with high heat input are avoided because zinc is lost from the alloy as vapour.
Typical Uses of Straight Red Brass Tube
Condenser tube, heat exchanger tube and instrument tubing
Heat exchanger shells, water boxes and flexible metal hose
Pump cylinder liners, radiator cores and pickling crates
Plumbing pipe, pipe nipples, service lines, traps and j-bends
Electrical conduit, rotor bars and screw shells
Builders hardware, kick plates, badges, nameplates and decorative metalwork
Inspection Points Before Dispatch
Heat specific chemical analysis with copper inside 84.0 - 86.0 %
Tensile and elongation test for the ordered temper
Hydrostatic proof test of the finished tube
Eddy current examination over the full length
Diameter, wall, eccentricity, straightness and length verification
FAQ
Q: Why is straight tube preferred for condensers?
Straight lengths with uniform wall expand evenly into the tubesheet, are simple to support with baffles and can be replaced individually without reworking the rest of the bundle.
Q: Which standard applies to condenser and heat exchanger tube?
Copper alloy tube for condensers and heat exchangers is specified to ASTM B111 or the equivalent ASME SB111, which define chemistry, temper, mechanical properties and tolerances.
Q: What is the difference between this tube and a copper water tube?
Red brass contains about 15 % zinc, which raises strength and improves resistance to dezincification, while copper water tube grades are essentially pure copper with very high conductivity.
Q: Can the tube be welded into a shell assembly?
Brazing and soldering are preferred. Gas shielded arc welding is possible with controlled heat input, but processes that overheat the metal are avoided because zinc evaporates from the alloy.
Q: What temper is used for tube that will be roller expanded?
Annealed tube is normally specified, since it must deform plastically against the tubesheet wall without cracking during expansion.
Q: Is the alloy suitable for seawater cooling circuits?
It performs well in seawater and brackish water when the wall includes a corrosion allowance and stagnant aerated zones are avoided in the circuit design.




