Oct 30, 2025 Leave a message

ASTM B43 C23000 85/15 Red Brass Seamless Round Pipe for Water and Industrial Lines

ASTM B43 C23000 seamless round pipe is the 85/15 red brass product used in plumbing, potable water lines, heating circuits and general industrial piping. The alloy sits between pure copper and the yellow brasses: it carries enough zinc to give useful strength and machinability, yet keeps enough copper to maintain the warm red colour and the corrosion behaviour that made it a traditional choice for water service.

What Is ASTM B43 C23000 Red Brass Pipe?

ASTM B43 covers seamless red brass pipe produced in standard and non standard nominal sizes, supplied in the drawn tempers that piping systems require. C23000 is the UNS designation of the 85/15 red brass alloy, sometimes written CDA 230, with a nominal composition of 85 % copper and 15 % zinc. The same material appears in national systems under the designations CuZn15, CW502L, CZ102, C2300 and DIN 2.0240, which allows an existing specification to be translated without changing the metallurgy.

Because the pipe is produced seamless, it has no longitudinal weld and therefore no weld zone to consider in pressure, bending or corrosion calculations. That is important in hot water circulation and in heat exchanger work, where the pipe may be bent into U shapes or rolled into a tube sheet.

Chemical Composition of C23000 Red Brass

Element Content Function
Copper (Cu) 84.0 – 86.0 % Base of the alloy, corrosion resistance
Zinc (Zn) Remainder Solid solution strengthening
Lead (Pb) 0.05 % max Controlled residual
Iron (Fe) 0.05 % max Controlled residual
Total other elements 0.15 % max Includes tin and antimony

The high copper content keeps C23000 in the single phase alpha range at ambient temperature, so the alloy is not susceptible to the beta phase selective attack that affects higher zinc brasses. Where aggressive or high chloride water is expected, an inhibited or higher copper alloy pipe is normally selected.

Standard Sizes and Temper Range

Parameter Options
Nominal pipe sizes 1/8 in to 4 in, plus metric equivalents
Outside diameter about 0.405 in to 4.500 in depending on size
Wall thickness Standard wall, schedule 40, schedule 80 and heavier on request
Form Seamless round pipe and tube, straight lengths
Length Custom cut lengths, commonly 3 m, 5.8 m and 6 m
Temper O61 annealed, H55 light drawn, H58 drawn, H80 hard drawn
Ends Plain, threaded, bevelled or capped

Typical Mechanical Properties

Temper Tensile strength Yield strength Elongation
Annealed (O61) about 275 MPa / 40 ksi about 83 MPa / 12 ksi about 60 %
Light drawn (H55) about 345 MPa / 50 ksi about 275 MPa / 40 ksi about 30 %
Hard drawn (H80) about 480 MPa / 70 ksi about 415 MPa / 60 ksi about 8 %

These values are typical published data for C23000 pipe. Annealed pipe is used where the run must be bent or coiled, while drawn and hard drawn pipe are selected for straight pressure lines, threaded connections and structural brackets that need stiffness.

Where C23000 85/15 Red Brass Pipe Is Used

Potable water service lines, rising mains and distribution pipework inside buildings.

Hot and cold domestic water systems, where the alloy has a long record of service.

Heating, ventilation and air conditioning water circuits, including fan coil and chiller pipework.

Heat exchanger and condenser tube, including finned tube and U-bend assemblies.

Steam condensate return lines, air lines and low pressure industrial process piping.

Gland and valve trim components, instrument lines and decorative architectural tube.

Corrosion Behaviour, Joining and Inspection

In neutral and moderately hard water the alloy forms a protective copper oxide and carbonate film that limits further metal loss.

Selective leaching of zinc is a recognised risk for brasses in some waters, and the low zinc content together with added inhibitor levels in the alloy family keeps C23000 in the more resistant group.

The pipe solders and brazes easily, and can also be threaded in the harder tempers where mechanical joints are preferred.

Inspection includes dimensional and wall thickness checks, tensile testing of the temper, flattening or expansion tests for ductility and, on request, eddy current or hydrostatic pressure testing.

Material certificates can be supplied as manufacturer or third party documents, and each bundle is marked so the heat number can be traced back to the cast.

FAQ

Q: What does 85/15 mean in red brass pipe?
It describes the nominal copper to zinc ratio of the alloy, roughly 85 % copper and 15 % zinc. In UNS terms the grade is C23000, and the same composition is known as CuZn15 in the European system.

Q: Is ASTM B43 pipe seamless?
Yes. ASTM B43 covers seamless red brass pipe in standard sizes, so there is no longitudinal weld seam. This makes the pipe suitable for bending, coiling and rolling into tube sheets.

Q: How does C23000 differ from C26000 cartridge brass?
C23000 contains more copper and less zinc, which improves corrosion resistance and colour stability. C26000 has higher zinc and is stronger and more machinable, but it is used less often in potable water pipework.

Q: Can the pipe be threaded?
Threading is practical in the drawn and hard drawn tempers, where the wall is thick enough and the material is stiff enough to take a clean thread. Annealed pipe is usually joined by soldering or brazing instead.

Q: What sizes and lengths are available?
Nominal sizes from 1/8 in to 4 in are produced, along with metric outside diameters, in standard wall and schedule 40 or schedule 80 thicknesses. Straight lengths are cut to order, commonly 3 m to 6 m.

Q: Which applications should avoid this alloy?
Very aggressive waters with high chloride content, strongly acidic condensates and high velocity seawater are better served by copper-nickel or higher nickel alloys, where the protective film is more stable.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry