Oct 24, 2025 Leave a message

ASTM B111 CDA 101 OFE Copper Light Drawn Tube for Electronic Applications

What ASTM B111 CDA 101 OFE Copper Tube Is

ASTM B111/B111M covers seamless copper and copper alloy tube intended for condensers, evaporators and heat exchangers. UNS C10100, historically listed as CDA 101 and known as oxygen-free electronic (OFE) copper, is the highest purity copper grade in that family. It is melted and cast under a controlled atmosphere so that oxygen is physically excluded rather than neutralised with phosphorus. The result is copper with a minimum content of 99.99 % and residual oxygen of no more than 0.0005 %, a combination that keeps electrical conductivity at or above 101 % IACS while removing any risk of hydrogen embrittlement during brazing, welding or bright annealing in a reducing atmosphere.

In the light drawn condition (temper H55) the tube receives a moderate cold reduction after the final anneal. This raises tensile and yield strength above the soft annealed tempers while preserving enough elongation for coiling, bending, flaring and roller expansion into a tubesheet. Light drawn OFE tube is therefore the usual selection when a component needs a stiff, dimensionally stable tube rather than a fully soft one, such as vacuum tube parts, bus connections and liquid-cooled power electronics.

Chemical Composition of UNS C10100

Element Requirement
Copper (Cu) 99.99 % minimum
Oxygen (O) 0.0005 % maximum
Total of all other elements 0.01 % maximum

Because the total allowance for every other element is only 0.01 %, the grade is effectively free of the deoxidisers and tramp elements that lower conductivity in ordinary fire-refined copper. Mill certificates for C10100 normally report the copper assay, the oxygen result and the residual element total as separate line items.

Mechanical and Physical Properties

Temper Temper code Tensile strength (typical) Yield at 0.5 % extension (typical) Elongation
Light drawn H55 35 ksi (240 MPa) 32 ksi (220 MPa) 25 %
Annealed, nominal grain 0.025 mm OS025 32 ksi (220 MPa) 10 ksi (70 MPa) 45 %
Hard drawn H80 55 ksi (380 MPa) 50 ksi (345 MPa) 8 %

Physical data for the annealed material: density 8.91 g/cm³, solidus 1065 C and liquidus 1083 C, electrical conductivity 101 % IACS, thermal conductivity about 391 W/(m·K), specific heat 0.385 kJ/(kg.K) and modulus of elasticity about 117 GPa. The very low oxygen content keeps these values stable after thermal cycling, which is why the grade is preferred over phosphorus-deoxidised copper in high-vacuum and radio-frequency hardware.

Standard Sizes of OFE Copper Tube

Outside diameter (in / mm) Wall (in / mm)
0.1880 / 4.78 0.032 / 0.81
0.2500 / 6.35 0.032 / 0.81
0.3750 / 9.53 0.065 / 1.65
0.5000 / 12.70 0.065 / 1.65
0.6250 / 15.88 0.065 / 1.65
0.7500 / 19.05 0.125 / 3.18
1.0000 / 25.40 0.125 / 3.18
1.5000 / 38.10 0.125 / 3.18
2.2500 / 57.15 0.125 / 3.18

Drawn tube is supplied straight in random or fixed lengths up to about 6 m, with the surface protected against handling marks. Wall thickness, outside diameter and wall eccentricity are controlled to the tolerances stated in ASTM B111/B111M, and the tube ends are deburred and capped for shipment.

Applications of C10100 OFE Copper Tubing

Vacuum tube, magnetron and radio-frequency cavity components where residual oxygen would outgas or embrittle the part.

Power substation bus tube, connectors and terminal hardware that must carry high current with minimum resistive loss.

Liquid-cooled cold plates, induction coils and power electronics cooling loops.

Heat exchanger and condenser tube in oxygen-sensitive or semiconductor process systems.

Brazed assemblies that are processed in reducing or vacuum furnaces.

Waveguide, coaxial conductor and high-purity gas distribution lines.

Fabrication, Cleaning and Inspection

C10100 tube is readily bent, coiled, flared, swaged and roll expanded. Because the grade contains no residual deoxidiser, it can be brazed in vacuum or in a hydrogen-bearing atmosphere without the internal steam reaction that causes cracking in ordinary copper. Welding is normally done by gas tungsten arc or electron beam using matching filler, with the joint area cleaned of oil and oxide immediately before joining. For vacuum and electronic service the tube is supplied clean and capped, and handling with bare hands is avoided.

Inspection follows ASTM B111/B111M for tension, flattening, flaring and expansion properties, with hydrostatic or pneumatic proof testing as ordered. Eddy current examination of copper and copper alloy tube is carried out to the practice described in ASTM E243, which detects longitudinal and circumferential discontinuities without damaging the finished surface. Related specifications that are frequently cited together with this grade include ASME SB111 for pressure equipment, ASTM B75/B75M for seamless copper tube, ASTM B188 for seamless copper bus pipe, and ASTM B359/B359M for integral-fin tube.

FAQ

Q: What does the OFE designation mean for copper tube?
OFE stands for oxygen-free electronic. The metal is melted and cast so that oxygen is excluded instead of being neutralised with phosphorus, giving a minimum copper content of 99.99 % and residual oxygen of 0.0005 % or less.

Q: Why is C10100 chosen instead of C12200 for some heat exchanger duties?
C10100 offers higher conductivity, above 101 % IACS, and is immune to hydrogen embrittlement during brazing. C12200 uses phosphorus for deoxidation, which slightly lowers conductivity but costs less, so it suits large water-side heat exchanger bundles.

Q: What is the H55 light drawn temper used for?
H55 gives a moderate amount of cold work, so the tube is stronger and stiffer than annealed tube while still ductile enough for coiling, bending and roller expansion into a tubesheet.

Q: How is the tube tested before delivery?
Tensile, flattening, flaring and expansion tests are performed to ASTM B111/B111M, hydrostatic or pneumatic proof testing is applied when specified, and eddy current examination is carried out to ASTM E243.

Q: Which sizes are normally stocked?
Outside diameters from about 4.78 mm to 57.15 mm with walls from 0.81 mm to 3.18 mm cover most vacuum, electrical and instrument-tube requirements, and other sizes can be drawn to order.

Q: Can this grade be welded rather than brazed?
Yes. Gas tungsten arc and electron beam welding are both used, with matching copper filler and immediate cleaning of the joint. Brazing remains the more common route because it avoids melting the tube wall.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry