Sep 16, 2025 Leave a message

C68700-Aluminum-Brass-Tube-.pdf

ASTM B111 C68700 Seamless Aluminum Brass Tube for Condensers and Evaporators

ASTM B111 C68700 is a seamless aluminum brass tube for surface condensers, evaporators and heat exchangers. The alloy is characterised by two features that matter in cooling water duty: resistance to the action of high-velocity salt water and black water, and a high tolerance of shock attack at the tube inlet. Tubes of this alloy are therefore recommended for cooling circuits in marine and land power stations where water velocities are high and where suspended solids can abrade the inlet end of the tube.

Why High Velocity Is the Governing Design Condition

In a condenser, the tube inlet sees the highest local velocity and the highest turbulence intensity of the whole circuit. Alloys that rely only on a copper oxide film erode in this zone, and the resulting horseshoe-shaped thinning at the inlet is the classic failure pattern of condenser tube. Aluminum brass forms an aluminum-rich film that is more resistant to mechanical removal, so the alloy tolerates both higher mean velocities and the local velocity peaks created by inlet geometry. The practical benefit is a longer interval between retubing campaigns and a lower risk of cooling water contamination of the condensate.

Composition and Mechanical Properties

Copper, Cu 76.0-79.0%
Aluminum, Al 1.8-2.5%
Arsenic, As 0.02-0.06%
Iron, Fe 0.06% max
Lead, Pb 0.07% max
Zinc, Zn remainder
Temper O61, annealed
Tensile strength, min 345 MPa (50 ksi)
Yield strength, min 125 MPa (18 ksi)

The BSI designation for the alloy is CZ110 and the ISO name is CuZn20Al2As. ASTM B111 applies to straight seamless tube, while ASTM B395 applies to U-bend tube made from the same alloy; ASME publishes equivalent requirements as SB111 and SB395. Where a condenser is retubed with U-bend tube, the bent portion is formed and stress relieved before the final test sequence, so the delivered U-bend carries a controlled residual stress level.

Physical Data for Thermal Design

Density: 8.33 g/cm³ (0.301 lb/in³)

Thermal conductivity: 100.4 W/(m·K) at 20 °C (58 Btu/(ft²·ft·h·°F) at 70 °F)

Specific heat capacity: 0.09 cal/(g·°C) at 20 °C

Coefficient of linear expansion: 18.5 × 10-6 per °C from 20 °C to 300 °C (10.3 × 10-6 per °F from 70 °F to 570 °F)

Melting range: 932-971 °C (1710-1780 °F)

Verification Tests Required by the Standard

Expansion test to Test Method B153, on samples selected for the purpose: the expanded tube must show no visible cracks or ruptures. Tube that has not received a final anneal is exempt.

Flattening test: the specimen is flattened at three positions along its length, each area rotated about one third of a turn, and the flattened section must pass a caliper set at three times the wall thickness. The flat areas are inspected for defects that would affect the intended application.

Residual stress test: ASTM B111 lists C68700 among the alloys that require either the mercury nitrate test (B154) or the ammonia vapour test (B858).

Eddy current test to Practice E243, performed on every tube over its full length.

Hydrostatic test at a fibre stress of 7000 psi (48 MPa) calculated with the thin-cylinder equation, with tube not normally tested above 1000 psi (7.0 MPa) unless the order states otherwise.

Applications

Surface condensers in marine power plants and on board ship, where seawater is the cooling medium

Land-based coastal power stations using once-through seawater cooling at high velocity

Evaporators and distillers in desalination plants

Process heat exchangers in refineries and chemical plants where brackish water is used

Ferrules and inlet-end components matched to the same alloy

Ordering and Handling Guidance

The order should state UNS C68700, the specification and edition in use, the temper O61, the outside diameter, wall thickness and length, and whether the tube is straight or U-bent. For U-bend tube the bend radius, the leg lengths and the bend plane orientation must also be defined, together with any requirement for a post-bend stress relief or for eddy current testing of the bent region. Tube should be handled with end caps in place, protected from impact, and stored away from standing water; bore contamination from site storage is a frequent cause of premature pitting that later appears as an eddy current indication.

FAQ

Q: What is C68700 tube used for?
It is used for condenser, evaporator and heat exchanger tubes, and for ferrules, mainly where seawater or brackish water is circulated at high velocity.

Q: Why is aluminum brass preferred over admiralty brass in some condensers?
Aluminum brass resists high-velocity water and shock attack better, so it is chosen where cooling water velocity is high or where the water carries abrasive solids.

Q: Is U-bend tube made to the same specification?
U-bend tube uses the same alloy and temper but is ordered to ASTM B395 (ASME SB395), which covers the bending, ovality and stress relief requirements for the bent section.

Q: What is the minimum tensile strength of the delivered tube?
345 MPa (50 ksi) in the O61 annealed temper, with a minimum yield strength of 125 MPa (18 ksi), both confirmed on the material test certificate.

Q: Which residual stress test is applied?
ASTM B111 permits either the mercury nitrate test to B154 or the ammonia vapour test to B858, and the manufacturer selects one unless the purchase order specifies which is to be used.

Q: How should the receiving inspection be planned?
Check the certificate against the order for grade, temper and dimensions, confirm the marking on each tube, and inspect the ends for ovality and mechanical damage before tubes are released to the retubing crew.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry