Sep 16, 2025 Leave a message

UNS-C44300-Admiralty-Brass-Tube.pdf

ASTM B111 C44300 O61 Annealed Seamless Brass Copper Round Tube

ASTM B111 C44300 O61 tube is seamless round tube in arsenical admiralty brass supplied in the annealed temper designated O61. The temper code is the key to the order: it fixes the mechanical property table that applies, the grain size that must be met, and the fabrication operations for which the tube is suitable.

Annealing softens the drawn tube and recrystallises the structure to a controlled grain size, restoring the elongation and formability needed for rolling into tubesheets, bending into U-shapes and flaring of tube ends. Where a tube must survive forming without cracking, O61 is the temper to specify rather than a drawn condition.

Material Definition and Applicable Standards

ASTM B111/B111M covers seamless tube and ferrule stock of copper and copper alloys up to 3 1/8 in. (80 mm) inclusive in diameter for surface condensers, evaporators and heat exchangers.

ASME SB111 applies identical requirements to equipment built under pressure vessel codes.

The C44300 composition is designated CuZn28Sn1As in the European system, covered by standards for seamless copper alloy heat exchanger tube such as EN 12451.

GB/T 8890 and JIS H3300 give the Chinese and Japanese equivalents, useful when a project mixes specifications.

O61 is the annealed temper of the specification; drawn tempers are available for straight tubes and are quoted separately.

Chemical Composition of C44300 and the O61 Temper

Element Requirement Notes
Cu 70.0 - 73.0 % Base metal
Sn 0.9 - 1.2 % Erosion resistance
As 0.02 - 0.06 % Dezincification inhibitor
Fe 0.06 % max Protects formability
Pb 0.07 % max Low for good working behaviour
Zn Remainder Balance of strength and conductivity

Annealing is carried out after the final drawing pass, and the resulting grain size is verified metallographically. A coarse grain improves ductility but may roughen the surface during forming, so the specification range is held deliberately narrow; suppliers state the nominal grain size requirement on the inspection certificate.

Mechanical Properties and Dimensions

Annealed C44300 tube is required to reach a minimum tensile strength of approximately 310 MPa and a minimum yield strength of approximately 105 MPa at 0.5 % extension under load.

Reported test values for annealed admiralty brass round tube typically fall in the range of about 331 to 379 MPa tensile and about 124 to 152 MPa yield, depending on size and wall.

Elongation in 50 mm is high in the annealed temper, which is what allows flaring, bending and rolling without cracking.

Hardness is verified to ASTM E18 where specified, and tension testing follows ASTM E8/E8M.

Expansion of the outside diameter at 20 % of the original diameter and the flattening test are standard acceptance tests for the annealed condition.

Round tube is supplied in outside diameters and wall thicknesses from the standard size tables within the 80 mm diameter limit of ASTM B111; larger round tubular products are ordered to other specifications.

Applications

Heat exchanger bundles and surface condensers where tubes are rolled or expanded into tubesheets.

U-bend and coil assemblies in condensers, evaporators and process heaters.

Feedwater heaters, coolers and refrigeration condensers fabricated from formed tubing.

Desalination evaporators and brine circuits requiring corrosion-resistant, formable tubing.

Replacement tube sets for existing admiralty brass bundles, where the annealed temper is essential to fit and roll the tubes.

Selection, Fabrication and Installation Guidance

Specify O61 whenever the tube will be bent, U-formed, flared or rolled. A drawn temper may meet the dimensional drawing but will fail during forming.

Confirm the nominal grain size on the certificate before forming operations, since grain size controls both bendability and the surface finish after bending.

Roll tubes with controlled expansion so that wall reduction stays within the joint specification; the soft temper tolerates expansion well but is easily over-rolled.

Stress relieve bent or heavily worked sections where service may involve ammonia, because brasses crack under stress corrosion in ammonia-bearing condensate.

Handle annealed tube carefully: it is soft and marks easily, and dents in the tube wall become sites of localised corrosion.

Inspection Points and Common Pitfalls

Check that the certificate states the O61 temper and the annealed grain size, not just the alloy grade.

Verify elongation and grain size rather than hardness alone when the tube must be formed.

Confirm that the ordered diameter lies inside the scope of ASTM B111, which ends at 3 1/8 in. (80 mm) for seamless tube.

Reject tube with deep handling marks, since the annealed surface has no work-hardened layer to resist local corrosion.

Keep tube dry, capped and free from chloride-bearing packing materials before installation.

FAQ

Q: What does the O61 temper mean?
O61 is the annealed temper designation used in ASTM B111. It identifies tube that has been annealed after drawing to a controlled grain size, giving high elongation and predictable forming behaviour.

Q: When should O61 be chosen instead of a drawn temper?
Choose O61 for any tube that will be bent, U-formed, flared or rolled into a tubesheet. Drawn tempers are used for straight tubes that must stay straight.

Q: What mechanical values are typical for annealed C44300 tube?
Minimum requirements are approximately 310 MPa tensile and 105 MPa yield at 0.5 % extension under load; typical reported values for annealed round tube lie around 331 to 379 MPa tensile and 124 to 152 MPa yield.

Q: Why is grain size checked on annealed tube?
Grain size determines ductility and surface behaviour during forming. Too coarse a grain gives a rough surface after bending, and too fine a grain reduces the elongation available for rolling.

Q: Is O61 tube suitable for seawater condensers?
Yes. The alloy itself is chosen for seawater resistance and the annealed temper is standard for condenser and heat exchanger bundles that are rolled into tubesheets.

Q: How is annealing carried out without damaging the alloy?
Annealing is performed after the final drawing pass under controlled temperature and atmosphere so that the C44300 grain structure recrystallises uniformly, then the grain size is verified metallographically before shipment.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry