What C44400 Antimonial Naval Brass Is
C44400 is a wrought copper-zinc alloy in the admiralty brass family, sometimes called antimonial admiralty metal. It is used almost exclusively as seamless condenser, heat-exchanger and cooling-water tube under the ASTM B111 / ASME SB111 specification, which covers seamless copper and copper alloy tube for surface condensers, evaporators and heat exchangers.
Admiralty brass was developed to resist the impingement attack and dezincification that plain 70/30 brass suffers in fast-flowing seawater. Three variants share the same base: C44300, inhibited with arsenic; C44400, inhibited with antimony; and C44500, inhibited with phosphorus. The tin addition present in all three raises resistance to erosion-corrosion, while the inhibitor element changes the electrochemical behaviour of the zinc-rich phase so that the alloy passivates instead of losing zinc.
Chemical Composition
The composition of C44400 is controlled to the following ranges under ASTM B111 / ASME SB111. Values are percentages by mass.
| Element | C44400 | Role |
|---|---|---|
| Copper (Cu) | 70.0–73.0 | matrix; sets strength and conductivity |
| Tin (Sn) | 0.9–1.2 | erosion-corrosion resistance |
| Antimony (Sb) | 0.02–0.10 | inhibitor against dezincification |
| Lead (Pb) | 0.07 max | residual; kept low for weldability and ductility |
| Iron (Fe) | 0.06 max | residual; controlled to protect conductivity |
| Zinc (Zn) | remainder | matrix balance |
| Other elements, total | 0.50 max | tramp element control |
The alloy contains no deliberate aluminium addition. Antimony and tin are the elements that control its corrosion performance, and purchasers who need an aluminium-bearing tube for seawater service should specify aluminium brass such as C68700 instead of expecting it from C44400.
Mechanical Properties and Standard Requirements
ASTM B111 / ASME SB111 sets minimum tensile strength, elongation and, for the annealed tempers, a maximum grain size for each alloy and temper that it covers. Because those limits change with the temper ordered - annealed O60 or O61, or hard-drawn H55 or H80 - the governing requirement is the limit printed in the standard for the specific temper, verified on a tensile test specimen cut from the finished tube.
Annealed tube: supplied for tubes that will be rolled or expanded into a tube sheet and for U-bend duty; typical producer values for annealed C44400 condenser tube fall in the 300–370 MPa tensile range with elongation of 30 % and above, and grain size is checked to confirm full recrystallisation.
Hard-drawn tube: higher tensile and lower elongation, used where rigidity and resistance to vibration are more important than forming.
Thermal conductivity: approximately 110 W/(m·K) at room temperature, roughly a quarter of that of pure copper but still high enough for condenser service.
Every tube is normally examined by eddy current after the final anneal, and a hydrostatic or pneumatic pressure test is performed where the purchase order requires it.
Applications in Marine and Cooling-Water Service
Surface condensers and heat exchangers: main and auxiliary condensers in ships and coastal power stations, where the cooling medium is unpolluted or slightly polluted seawater.
Desalination and seawater treatment: multi-stage flash and reverse osmosis plant heat exchangers, brine heaters and cooling water circuits.
Pumps, valves and fittings: bodies, impellers and trim for seawater service, and associated cast or wrought fittings.
Shipboard systems: lubricating oil coolers, fresh water coolers, air coolers and general seawater piping components, together with marine instruments and instrument housings.
Process industry: refinery and chemical plant exchangers working with clean or moderately aggressive cooling water.
Corrosion Behaviour and the Role of Antimony
The performance of C44400 in seawater is dominated by two mechanisms. The first is general corrosion, which is slow and produces a protective copper oxide and cuprous oxide film. The second is dezincification, in which zinc is selectively removed from the brass and a porous copper-rich residue is left behind; where that layer forms, mechanical strength collapses and the tube fails without warning.
Antimony acts as a cathodic inhibitor. It is added at a few hundred parts per million and modifies the surface film so that the zinc-rich beta phase is not preferentially attacked. The effect is specific to the alloy chemistry: C44400 is intended for clean and slightly polluted seawater at moderate velocity, and it is not a substitute for a copper-nickel alloy in heavily polluted, sulphide-bearing or high-velocity seawater, where C70600 or C71500 should be specified instead.
Manufacture, Fabrication and Inspection Points
Manufacturing route: casting of the billet, hot extrusion or piercing to a shell, cold drawing and pilgering with inter-annealing, and a final anneal to the ordered temper. The route is selected to produce a uniform, fine grain structure rather than simply to reach the finished dimensions.
Tube sheet expansion: annealed tube is expanded or roller-expanded into the tube sheet; expansion must not be so severe that the wall thins excessively at the ligament.
U-bend and stress relief: U-bends are formed on tube in the annealed condition and may be stress-relieved after bending to reduce the risk of stress-corrosion cracking in service.
Fabrication cleanliness: iron and carbon contamination on the tube surface promotes localised attack, so sawing, machining and storage procedures must exclude carbon steel tools and dirty racks.
Inspection: verify mill test certificate for composition and mechanical properties, eddy-current report, dimensional check on outside diameter, wall thickness and ovality, and grain size on the annealed temper.
FAQ
Q: What is the difference between C44300, C44400 and C44500?
All three are admiralty brass grades with the same copper, tin and zinc base. C44300 is inhibited with arsenic, C44400 with antimony and C44500 with phosphorus. The choice depends on the water chemistry and on the inhibitor that the plant specification calls for.
Q: Can C44400 be used for potable water?
It is normally selected for seawater and industrial cooling-water duty. Lead is restricted to 0.07 % maximum, and potable-water applications are usually placed with copper-nickel or phosphorus-deoxidised copper grades that have specific approvals for that service.
Q: Does C44400 contain aluminium?
No. Its corrosion resistance comes from tin and antimony. Where an aluminium-bearing tube is required for seawater service, aluminium brass such as C68700 is the correct specification.
Q: What temper should be ordered for a condenser retube?
Annealed tube is ordered when the tube must be expanded into the tube sheet or formed into a U-bend; hard-drawn tube is ordered for straight, rigid runs. The temper determines the tensile, elongation and grain-size limits that apply.
Q: How is C44400 tube tested before dispatch?
Eddy-current examination of the full length after the final anneal, tensile testing of a specimen, dimensional verification and, when the order requires it, a hydrostatic or pneumatic pressure test, all supported by a mill test certificate.
Q: When should a copper-nickel alloy be chosen instead?
For heavily polluted, sulphide-bearing or high-velocity seawater, and for systems where erosion-corrosion rather than simple dezincification governs life, C70600 or C71500 seamless tube gives better and more predictable performance.




