Where C60800 Fits in ASTM B111/B111M
ASTM B111/B111M covers seamless copper and copper-alloy condenser tubes and ferrule stock for condensers, evaporators and heat exchangers. Within that standard the aluminium bronze grade C60800 is the option chosen when chlorides, high flow velocity or abrasive suspended solids make the softer copper and brass grades unsuitable. The same grade appears in the equivalent ASME specification for pressure-retaining components, so a tube ordered to one is technically interchangeable with a tube ordered to the other, provided the temper and dimensions match.
Aluminium bronze differs from the plain copper grades in one important respect: it is selected for strength and corrosion resistance, not for conductivity. Its electrical and thermal conductivity are far lower than those of pure copper, so a designer who needs efficient heat transfer to a fluid relies on the tube wall thickness, the surface condition and the water velocity rather than on exceptionally high metal conductivity. What C60800 offers in exchange is a tube that resists seawater attack and impingement erosion far better than copper while retaining enough ductility to be bent and rolled into a tube sheet.
Chemical Composition and Tube Dimensions
The composition of C60800 is defined by controlled aluminium and arsenic additions to copper. Aluminium builds the protective aluminium-rich surface film and provides solid-solution strengthening; arsenic is present at a low, deliberately controlled level and improves the resistance of the alloy to attack in chloride-bearing waters.
| Element | Requirement | Contribution |
|---|---|---|
| Aluminium | 4.5 - 6.0 % | Solid-solution strengthening; forms the protective surface film |
| Arsenic | 0.02 - 0.35 % | Improves resistance to corrosion in chloride-bearing water |
| Copper and residuals | Copper balance, residual elements limited by ASTM B111/B111M | Matrix metal with controlled impurity levels |
Tube is produced by extrusion and drawing to the outside diameter and wall thickness called for in the heat-exchanger design, then finished by annealing, pickling and straightening. Common condenser sizes run from roughly 12 mm to 50 mm outside diameter with wall thicknesses of about 0.7 mm to 2.5 mm, supplied in straight lengths or as U-bent tubes. Dimensional tolerances on diameter, wall thickness, straightness and length are those of ASTM B111/B111M, and wall thickness tolerance in particular should be confirmed against the design allowance, since the corrosion allowance of a seawater tube is limited.
Performance Characteristics
Strength is the first advantage. The aluminium addition raises the yield and tensile strength of the tube well above the values obtained from copper or from admiralty brass, so a thinner wall can carry the same internal pressure, and the tube tolerates the mechanical loads imposed by tube-sheet rolling, support plates and vibration. In the annealed condition typical tensile strength falls in the range of about 400 to 480 MPa with yield strength of roughly 170 to 250 MPa and elongation of 20 % or more; the mandatory minima for the ordered temper are those printed in the standard, and higher strength can be obtained in cold-worked tempers.
Corrosion resistance is the second advantage, and the reason the grade is used in seawater. In contact with chloride-bearing water the alloy develops a dense, adherent aluminium-rich oxide film that limits further attack. The film re-forms after mechanical damage, which gives the material useful resistance to impingement and to the thin-film erosion that occurs at the inlet end of a condenser tube. The controlled arsenic addition further improves behaviour in aggressive waters. Applications in marine engineering, desalination, chemical plant and water treatment equipment all follow from this behaviour.
Wear behaviour is a related benefit. Under sliding contact a lubricating oxide layer forms on the aluminium bronze surface and reduces the friction coefficient, so the tube and the components around it keep their dimensions in service where copper or brass would wear more quickly. The material also has a moderate coefficient of thermal expansion, typically lower than that of the high-zinc brasses, which keeps dimensional change across the operating temperature range within predictable limits.
Fabrication behaviour is good but not unlimited. C60800 bends and rolls well in the annealed temper, which is why U-bending is carried out before final installation, and the tubes are attached to the tube sheet by roller expansion rather than by welding. Welding of aluminium bronze requires skill, a matching filler metal and careful removal of the refractory oxide, so welded joints are normally confined to the tube-sheet side and to headers rather than to the tubes themselves. Brazing is used for fittings and for instrumentation connections where a leak-tight joint is required.
Typical Applications
The grade is specified wherever a tube must survive chlorides, velocity and moderate temperature at the same time:
Steam surface condensers and auxiliary heat exchangers in power generation, where cooling water is seawater or brackish water.
Multi-stage flash and multi-effect desalination plants, including brine heaters and preheaters.
Chemical and petrochemical heat exchangers handling chlorides, seawater or ammoniacal process streams that require separate stress-corrosion evaluation.
Shipboard seawater systems: main and auxiliary condensers, lube oil coolers, fresh water generators and jacket water coolers.
Cooling water exchangers in refineries, steel plants and large air-conditioning plants using open-circuit or tower water.
In each of these duties the selection decision normally comes down to a comparison with admiralty brass and with copper-nickel alloys. C60800 is chosen where strength at the tube sheet, resistance to impingement at the inlet, and freedom from the pitting that affects the lower-alloyed grades in polluted water are the decisive factors.
Installation, Handling and Inspection
Aluminium bronze tubes are delivered in the annealed temper for bending and rolling. Handling practice follows the usual rules for thin-wall copper alloy tube: tubes are stored horizontally on padded supports, protected from surface abrasion, and kept free of carbon steel contact that could introduce galvanic corrosion during storage. Bending is performed with a mandrel to control ovality and wall thinning in the bend, and the bent leg is stress-relieved before rolling where the bend radius is tight.
Attachment to the tube sheet is by roller expansion, and the tightness of the joint depends on hole preparation, expansion rate and cleanliness rather than on the tube material alone. Recommended inspection and test practice for the finished exchanger includes the following points:
Verification of the tube certificate against ASTM B111/B111M for chemistry, temper, dimensions and mechanical properties.
Eddy-current examination of the tubes to the practice in ASTM E243, which detects wall defects, cracks and thickness variation before installation.
Expansion and flattening tests on samples to confirm that the temper is ductile enough for the forming operation.
Hydrostatic or pneumatic pressure testing of the assembled exchanger, followed by a leak test of every rolled joint.
Documentation of heat numbers and tube positions so that service inspection results can be traced back to a specific lot.
FAQ
Q: Is C60800 a copper tube or an aluminium tube?
It is a copper alloy tube. Aluminium is an alloying addition at 4.5 to 6.0 %, with copper as the balance, so the material behaves as a copper-based alloy with the strength and the seawater resistance that the aluminium addition provides.
Q: Is C60800 suitable for seawater cooling water?
Yes. It forms a protective aluminium-rich surface film in chloride-bearing water and resists impingement and erosion, which is why it is used in power station condensers, shipboard seawater coolers and desalination plants.
Q: How does it compare with admiralty brass for heat exchanger tube?
It is stronger and more resistant to impingement attack at the tube inlet, and it is not subject to the dezincification mechanism that affects zinc-rich brasses. Admiralty brass remains a lower-cost option where water chemistry and velocity are benign.
Q: Does it conduct heat well?
Its thermal conductivity is well below that of pure copper, because aluminium in solid solution scatters both electrons and phonons. The grade is chosen for durability in seawater rather than for maximum heat transfer, and the exchanger is designed around its properties.
Q: Can C60800 tubes be welded?
They can be welded with matching filler and careful oxide removal, but tubes are normally attached to the tube sheet by roller expansion. Welded joints are generally limited to headers, fittings and instrumentation connections.
Q: Why is arsenic added to the alloy?
Arsenic is added at a controlled low level to improve the resistance of the alloy to corrosion in chloride-bearing waters. It is held within the narrow range specified in ASTM B111/B111M so that the mechanical properties and the weldability of the tube are not affected.




