C61400 Aluminum Bronze: Definition and Scope
UNS C61400 is a wrought aluminum bronze in which aluminium is the principal alloying addition to copper and iron acts as both a strengthener and a grain refiner. It is not a copper-zinc-tin alloy, and the alpha, beta and gamma phase terminology that belongs to the brasses does not describe this grade. The alloy is supplied commercially as rod and bar to ASTM B150/B150M, as plate, sheet and strip to ASTM B171/B171M, and as seamless condenser and heat-exchanger tube to ASTM B111/B111M. Forgings and machined components are produced from those mill forms.
Because the grade is chosen for strength combined with seawater service rather than for electrical conduction, two factors control its behaviour: how much aluminium is held in solid solution in the copper lattice, and how the iron-rich intermetallic particles are sized and distributed. Both are fixed during melting, casting and hot working, so the microstructure of the delivered product is as important as the chemistry printed on the mill certificate.
Chemical Composition and Phase Structure
The product standards use the same limiting ranges for the two alloying elements, and the balance is copper with specified residual limits on zinc, manganese, nickel and other elements. Aluminium provides solid-solution strengthening and also governs which phases can form, while iron has very low solubility in the copper-rich matrix and combines with aluminium to form discrete intermetallic particles.
| Element | Typical requirement | Function |
|---|---|---|
| Aluminium | 6.0 - 8.0 % | Solid-solution strengthening; controls phase balance and the protective surface film |
| Iron | 1.5 - 3.5 % | Forms iron-aluminium intermetallic particles and refines the cast grain structure |
| Copper | Balance, normally about 90 % | Matrix metal; supplies thermal conductivity and ductility |
| Zinc, manganese, nickel and residuals | Limited by ASTM B150/B150M, B171/B171M and B111/B111M | Kept low to avoid unwanted phase changes and loss of ductility |
Within the aluminium range covered by C61400, the wrought structure consists of a face-centred-cubic alpha matrix together with iron-rich kappa phases based on iron aluminide. These particles appear in several morphologies depending on thermal history: coarse particles formed during solidification, finer particles precipitated in the solid state, and very fine dispersions that obstruct dislocation movement. That combination is what produces the strength of the grade together with its resistance to galling and erosion.
Cooling rate during solidification has a decisive effect on the as-cast structure. Rapid controlled cooling retains more aluminium in supersaturated solid solution and gives a finer dispersion of iron-rich particles after hot working, while slow cooling coarsens the particles and can leave continuous networks that reduce ductility. Hot working is therefore carried out in a controlled temperature window below the point at which a beta phase field would appear, so that the finished product remains an alpha-plus-kappa structure.
Mechanical Properties
C61400 combines a tensile strength well above that of the common alpha brasses with a yield strength that is higher still in relative terms, while elongation remains adequate for forming and for interference fits. The mandatory minima for a given product form and temper are set by the applicable product standard; the ranges below are indicative of normal commercial supply and are given as typical values rather than as specification limits.
| Property | Typical value, hot-worked or annealed | Comment |
|---|---|---|
| Tensile strength, Rm | about 480 - 560 MPa | Higher values are reached in cold-worked tempers |
| Yield strength, Rp0.2 | about 200 - 290 MPa | Substantially above alpha brass at equal temper |
| Elongation, A5 | 25 % or more in the annealed condition | Falls as cold reduction increases |
| Hardness | about 110 - 160 HBW | Tracks the volume fraction and dispersion of kappa phase |
| Modulus of elasticity | about 117 GPa | Used for stiffness-limited designs |
Two points matter when this table is used for design work. First, C61400 is not strengthened by precipitation heat treatment: strength comes from aluminium in solid solution, from the intermetallic particles and from cold work, so a conventional hardening cycle does not apply. Second, tensile properties decrease gradually at elevated temperature while the alloy keeps useful toughness, which makes it acceptable for moderately warm seawater and process streams rather than for high-temperature pressure service.
Corrosion and Wear Behaviour in Service
C61400 is specified for pumps, valves and marine hardware because of its behaviour in chloride-bearing environments. An aluminium-rich protective film forms rapidly on a freshly machined or abraded surface and re-forms after damage, giving good resistance to general seawater corrosion and to impingement and cavitation erosion. The iron addition supports the stability of that film. Service experience in seawater piping, valve trim and marine shafting reflects this combination rather than any single alloying element.
The main limitation is sensitivity to ammoniacal environments. Aluminium bronzes can suffer stress-corrosion cracking when exposed to ammonia or ammonium compounds while under stress, and that risk is evaluated by an ammoniacal test such as ASTM B858 rather than assumed from chemistry alone. Residual stress from machining or bending should therefore be relieved before a part enters ammonia-bearing service. Selective attack of a high-zinc phase is a brass problem rather than an aluminium bronze problem, because C61400 contains no continuous zinc-rich phase.
Wear resistance follows the same structure. The hard intermetallic particles carry load and resist metal-to-metal contact, which is why the grade is used for worm gears, wear strips and pump wear rings, and why it is often paired with a hardened steel counterface. Where fretting or galling is expected, surface finish and lubrication practice matter as much as alloy selection.
Processing, Heat Treatment and Inspection
C61400 is readily machined, hot formed and cold formed, but each operation has a preferred window. Hot working is carried out in the temperature range normally recommended for aluminum bronze, with a finishing temperature high enough to avoid cracking and low enough to preserve the fine kappa dispersion. Cold working raises strength and hardness, with the amount of reduction limited by the fall in elongation. Stress-relief annealing, typically in the 500 - 650 degrees Celsius band followed by controlled cooling, restores ductility and reduces distortion and residual stress without excessive coarsening of the structure.
Joining is carried out by brazing, by gas-shielded arc welding with matching filler, and by friction and resistance methods. Welded joints are usually made in the annealed condition and are inspected for porosity, because aluminium bronzes form a tenacious refractory oxide that can be trapped at the fusion boundary. For condenser tube, expansion into the tube sheet is the normal method of attachment rather than welding.
A practical incoming inspection sequence for exported C61400 product covers the following points:
Verification of the heat analysis against ASTM B150/B150M, B171/B171M or B111/B111M as applicable, reported on the mill certificate.
Tensile testing to ASTM E8/E8M and hardness testing to ASTM E18 on samples taken at the frequency defined in the purchase order.
Metallographic examination of grain size and kappa phase distribution using the grain-size practice of ASTM E112.
Non-destructive examination: ultrasonic or eddy-current testing for tube and bar, liquid penetrant testing for machined and welded surfaces.
Where the end use involves ammonia or ammonium compounds, an ammoniacal stress-corrosion test to ASTM B858.
Dimensional verification, marking and traceable documentation so that the heat number on the certificate can be matched to the finished part.
FAQ
Q: Is C61400 a brass or a bronze?
It is an aluminum bronze. The alloying system is copper-aluminium-iron, so the alpha, beta and gamma phase language used for brasses does not describe it, and its zinc content is a controlled residual rather than a main constituent.
Q: Can C61400 be hardened by heat treatment?
No. Strengthening comes from aluminium in solid solution, from iron-aluminium intermetallic particles and from cold work. Heat treatment is used for annealing and stress relief, not for hardening.
Q: How does its strength compare with ordinary brass?
In comparable tempers the yield strength of C61400 is substantially higher than that of alpha brasses such as C26000, while elongation remains sufficient for forming, which is why it is chosen for load-bearing fittings and pump parts.
Q: Is it suitable for seawater service?
Yes. It resists general seawater corrosion, impingement and cavitation and is widely used in pumps, valves, condenser tube sheets and marine hardware. Ammoniacal service requires separate evaluation by an ASTM B858 test.
Q: Which mill forms are available?
The usual forms are rod and bar to ASTM B150/B150M, plate, sheet and strip to ASTM B171/B171M, and seamless tube to ASTM B111/B111M, with forged and machined parts produced from these forms.
Q: Why does the casting cooling rate matter?
It determines how much aluminium stays in solid solution and how finely the iron-rich particles are dispersed. Fast controlled cooling followed by correct hot working gives a uniform alpha-plus-kappa structure with good ductility and stable properties.




