May 21, 2025 Leave a message

Copper Tubes for Electric Heaters: C12200, C12000 and C11000 Material Guide

What Copper Tubes Do in Electric Heating Elements

An electric heating element is built around a metal sheath tube that houses the resistance wire and the densely compacted magnesium oxide insulation. The sheath is the only part of the element that touches the heated medium, so it has to serve three duties at once: transfer heat efficiently, resist the working environment, and stay leak-tight for the whole service life of the appliance. Copper is selected for a large share of these elements because of its thermal conductivity, its ductility and its resistance to fresh water and to many process fluids.

The sheath is normally a seamless drawn copper tube supplied in the soft annealed temper so that it can be bent to the tight radii required by immersion heaters, cartridge heaters, oil heaters, fan heaters and appliance elements. The grades used are almost always the phosphorus-deoxidized coppers C12200 and C12000, with C11000 appearing in a minority of designs where maximum conductivity is the priority.

Common Copper Grades for Heater Sheath Tubes

C12200 (phosphorus-deoxidized copper, high residual phosphorus, DHP). This is the standard workhorse grade for copper heater tubes. A controlled residual phosphorus content deoxidizes the melt, which removes the risk of steam embrittlement when the tube is annealed or brazed in a reducing or hydrogen-bearing atmosphere. It is supplied as seamless tube in soft, half-hard and hard tempers and is easy to bend, flare and braze.

C12000 (phosphorus-deoxidized copper, low residual phosphorus, DLP). C12000 carries a lower residual phosphorus level than C12200, so it keeps the fully deoxidized structure while retaining higher electrical and thermal conductivity. It is a common choice where the element also has to carry current, or where the thermal duty is particularly demanding.

C11000 (electrolytic tough pitch copper, ETP). C11000 is refined copper with an oxygen content of 0.02 % to 0.04 %. It offers the highest conductivity of the three grades, but the oxygen it contains reacts with hydrogen at elevated temperature and can cause intergranular embrittlement during furnace brazing or bright annealing in a reducing atmosphere. Where that kind of processing is involved, C12200 or C12000 should be substituted.

Typical Property Comparison

Property C12200 (DHP) C12000 (DLP) C11000 (ETP)
Base composition Copper with high residual phosphorus Copper with low residual phosphorus Copper with 0.02 to 0.04 % oxygen
Deoxidation Fully deoxidized Fully deoxidized Not deoxidized, tough pitch
Hydrogen embrittlement risk Very low Very low Significant when heated in reducing atmospheres
Electrical conductivity Reduced by residual phosphorus Higher than C12200 Reference grade for 100 % IACS annealed copper
Thermal conductivity High Higher than C12200 Highest of the three
Formability and brazing Excellent Excellent Excellent, subject to the embrittlement note
Density About 8.9 g/cm³ About 8.9 g/cm³ About 8.9 g/cm³

Pure copper melts at about 1083 °C, and the small phosphorus or oxygen additions in these grades do not shift the melting range appreciably. Density stays close to 8.9 g/cm³ in all three. Mechanical properties are governed by temper rather than by grade: soft annealed tube is used for bending, half-hard tube is chosen where the sheath must resist deformation during swaging or where higher hoop strength is wanted, and hard temper is reserved for straight elements that are not formed after assembly.

Where Copper Sheath Tubes Are Used

Immersion and screw-plug heaters for water, oils and mildly corrosive liquids

Cartridge and tubular heaters in packaging, moulding and food service equipment

Domestic appliance elements such as kettles, washing machines and dishwashers

Crankcase and compressor heaters in refrigeration and HVAC equipment

Electric duct heaters and process heating elements in industrial plant

Copper is not the universal answer for every medium. Strongly ammoniacal, cyanide-bearing or heavily chlorinated solutions attack copper, and for those duties a stainless steel or nickel alloy sheath is normally specified. The grades described here suit water, steam, oils and neutral fluids, which cover the great majority of electric heating applications.

Selection and Fabrication Points

Wall thickness follows the design pressure and the bending radius. Thinner walls bend more easily but reduce pressure capability and the reserve against erosion. The tube should be ordered against a cleanliness specification, because drawing lubricant and oxide left inside the bore contaminate the magnesium oxide fill and cause premature element failure. Dimensional tolerances, ovality and straightness should also be agreed before ordering, since they decide whether the bending and filling equipment can run without scrap.

When brazing, use a filler compatible with the tube grade and avoid long dwell times at high temperature; the aim is a sound joint without over-annealing the sheath. For C12200 and C12000, brazing in a hydrogen-bearing furnace atmosphere is not a problem. For C11000 it is, so that grade should be joined in air with flux, or by a process that keeps hydrogen away from hot metal. Welding of copper sheath tubes is normally limited to the end fittings and is done with processes that control heat input closely.

Inspection and Common Pitfalls

Check diameter, wall thickness and straightness against the purchase order before bending.

Eddy-current or pneumatic testing to confirm the tube is sound over its full length.

Check grain size and hardness to confirm that the temper suits the forming operation.

Confirm that the bore is degreased and capped; contaminated tube is a frequent cause of failure.

Two mistakes recur in production. The first is substituting C11000 for C12200 to save cost and then brazing the assembly in a hydrogen atmosphere, which produces brittle joints. The second is over-bending annealed tube without an internal mandrel, which ovalises the bore and thins the outer wall. Both are avoided by fixing the grade, temper and forming route at the quotation stage.

FAQ

Q: Which copper grade is best for a water heater sheath tube?
C12200 is the most widely used because it is fully deoxidized and tolerates reducing furnace atmospheres during brazing. C12000 is selected when higher thermal or electrical conductivity is required.

Q: Can C11000 be used for electric heating elements?
Yes, provided the element is not annealed or brazed in a hydrogen-bearing atmosphere. Otherwise the oxygen in the copper reacts with hydrogen and the tube becomes brittle.

Q: What temper should be ordered for bending?
Soft annealed tube is standard for bending to small radii. Half-hard temper is used where the sheath must resist deformation, and hard temper for straight elements.

Q: Does the copper sheath affect the heating rate?
Yes. Copper has very high thermal conductivity, so heat passes from the resistance wire to the medium quickly and the sheath runs at a lower temperature for the same power output.

Q: Is copper suitable for oil heaters?
Yes. Copper resists oxidation in mineral and synthetic oils at normal heater operating temperatures and is a common sheath material for oil immersion elements.

Q: How is the tube tested before shipment?
Seamless tube is normally checked by eddy-current testing and a pneumatic or hydrostatic leak test, with dimensions, hardness and surface condition inspected to the order specification.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry