Why Reaming Copper Tube Matters
Every time a copper tube is cut with a wheel-type cutter, the cutting wheel displaces metal rather than removing it cleanly. The result is an external ridge and an internal burr that reduces the bore, disturbs refrigerant or water flow and acts as a stress raiser at the joint. In refrigeration and air conditioning work to ASTM B280, and in plumbing work to ASTM B88 and EN 1057, that burr must be removed before the tube is assembled and brazed.
A reamer is the tool that restores the bore to its nominal diameter. It is not a cutter for making holes larger, and it is not a substitute for a deburring brush: it removes the rolled-over lip only, leaving the wall thickness unchanged. Done correctly, reaming takes a few seconds per tube end and prevents two of the most common causes of leaky joints - a burr that holds the tube off the fitting seat, and a thin metal flap that later fractures in service.
Tool Selection and Preparation
Reamers for copper tube come in three main forms, and the right choice depends on the tube size and the access available.
| Reamer type | Best suited to | Notes |
|---|---|---|
| Inner-out deburring tool with blade | Small to medium tube, on-site work | Also removes the external ridge when reversed |
| Spiral or fluted reamer | General workshop use | Self-centring, quick metal removal |
| Hand-held reaming pen or scraper | Small bore tube in tight spaces | Slow but controllable, useful in service work |
| Powered reamer attachment | Repetitive production cutting | Requires controlled speed to avoid over-cutting |
Before starting, confirm the tube size and wall thickness, check that the reamer is sharp and free from damage, and clean the tool of any metal particles left from previous use. A blunt reamer burnishes and work-hardens the bore instead of cutting cleanly, which makes the joint harder to braze and leaves a rough finish.
Step-by-Step Reaming Procedure
Support the tube. Clamp it in a vice with soft jaws or hold it in a fixture so that it cannot rotate or slide; never clamp directly on a finished surface with hard jaws.
Square the end. Use a tube cutter to obtain a clean square cut, and remove the external ridge with the deburring side of the tool or a fine file held flat against the end.
Insert the reamer squarely into the bore. Keep the tool axis aligned with the tube axis; an angled start produces an oval bore and an uneven wall.
Rotate the reamer with steady, moderate pressure. Two or three full turns in the cutting direction are normally enough for a thin-wall tube; do not force the tool or lever it sideways.
Withdraw the reamer and inspect. Check that the internal lip has been removed and that the bore surface is smooth and bright, without chatter marks.
Clean the tube end. Blow out or wipe away all chips and cutting residue, inside and out, before the joint is assembled.
The whole operation should take a few seconds per end. If it takes longer, the reamer is blunt or the wrong size; if the tube wall suddenly becomes thin, the tool has been allowed to over-cut. Both conditions warrant stopping and changing the tool.
Working With Thin-Wall and Coiled Tube
Annealed refrigeration tube supplied in coils has a thin wall and a soft temper, so it deforms very easily. Support the coil so that the tube end is straight for at least a few diameters before the cut, and use light, concentric pressure only. For small-bore instrument tube, hand reaming with a pen-type tool is safer than a powered reamer, because the tool cannot run away and thin the wall.
Where tube ends are to be flared rather than brazed, the reaming step is doubly important. A burr left inside the end will score the flare cone and can start a crack at the base of the flare; the deburred and cleaned surface is what allows the flare to seat properly against the fitting.
Inspection After Reaming
Bore diameter: the reamed end should pass the same gauge or the mating tube should slide in freely without resistance.
Wall integrity: no thinning, no score marks deeper than the surface finish allowance, and no visible cracks at the cut end.
Cleanliness: the bore must be free of copper chips, dust and cutting lubricant residue, particularly for refrigerant circuits.
Squareness: the end face should be square to the axis so that the capillary gap in the fitting is uniform.
Protection: cap or tape the end after reaming so that moisture and dirt do not enter before assembly.
FAQ
Q: Is reaming necessary after cutting copper tube?
Yes. A wheel cutter rolls a burr into the bore, and leaving it in place reduces the internal diameter, prevents the tube from seating fully in the fitting and creates a stress concentration at the joint.
Q: Can I ream copper tube with a drill bit?
Not recommended. A twist drill removes wall material instead of the burr, will not follow the bore accurately and can easily thin or split a thin-wall tube.
Q: How deep should the reamer be inserted?
Only far enough to remove the rolled-over lip, which is normally well under a millimetre of material, just past the cut edge.
Q: How do I know when the reamer is blunt?
The tool skids, burnishes rather than cuts, produces chatter marks or requires much more pressure than usual; at that point it should be replaced or resharpened.
Q: Should lubricant be used when reaming copper?
A small amount of cutting lubricant reduces friction and improves finish, but all residue must be removed afterwards, because oil trapped in a refrigerant circuit causes problems in service.
Q: Does reaming change the outside diameter of the tube?
No. Reaming addresses the internal burr only; the external ridge is removed separately with the deburring edge of the tool or a fine file.




