What Grade Is C91300?
C91300 is a copper-based casting alloy that belongs to the leaded tin bronze family. The UNS system reserves the four-digit numbers beginning with C9 for cast copper alloys, so C91300 is supplied as cast product rather than as wrought sheet, strip or tube, and it should never be ordered as a substitute for a wrought brass or cupronickel. Within the bronze family its identity is set by two deliberate alloying additions: tin, which raises strength and gives the alloy its bearing characteristics, and lead, which is added for machinability and for the lubricating film it provides at a sliding surface. Copper forms the balance of the structure.
Why C91300 Is Not an Aluminium Bronze
One of the most common mix-ups in bronze purchasing is to describe C91300 as an aluminium bronze, or to quote an aluminium content of eight to ten per cent for it. That description belongs to entirely different alloys. Aluminium bronzes are the grades in which aluminium is the principal addition, commonly around nine to eleven per cent, and they are represented by the cast nickel-aluminium bronze family, for example C95800, or by the simpler aluminium bronzes such as C95400. Those materials are chosen for seawater pumps, propellers, valve bodies and high-load wear components because of the tough aluminium oxide film they form. C91300 works by a different mechanism, a tin-bearing copper matrix with lead dispersed through it, and it wins its place in bearings and bushings, not in high-velocity seawater impellers.
Composition and Cast Structure
Because tin and lead are the defining elements, the alloy is specified by UNS number together with a casting standard rather than by a single nominal analysis. Continuous casting and sand casting use separate specifications and can produce slightly different property balances, so the buyer should always state both the UNS number and the standard under which the part is to be supplied.
| Element | Role in C91300 |
|---|---|
| Copper (Cu) | Matrix of the alloy, balance of the composition |
| Tin (Sn) | Principal strengthening addition; gives bronze its bearing character |
| Lead (Pb) | Deliberate addition for machinability and for a low-friction sliding film |
| Zinc (Zn) | Present only at low residual levels in this family |
| Nickel (Ni), iron (Fe), manganese (Mn) | Not deliberate additions; held to residual limits |
Continuous cast bar and hollow bar are the usual mill forms for C91300. Continuous casting gives a sound, dense structure with a fine and uniform distribution of the lead phase, free from the porosity and shrinkage that can appear in heavier sand castings, and it is the reason the alloy is so often supplied as bushing stock from which finished parts are machined.
Properties That Matter in Service
The property profile of a leaded tin bronze is best understood as a set of bearing-oriented characteristics rather than as a table of headline strength values.
Load capacity: tin in solid solution strengthens the copper matrix, allowing the alloy to carry steady bearing loads in pumps, gearboxes and general machinery.
Embeddability: the soft lead phase absorbs small hard particles that would otherwise score a shaft, which is why leaded bronzes survive dirty or poorly filtered lubrication.
Conformability: the alloy can deflect slightly to accommodate small misalignments between shaft and housing.
Low friction and anti-seizure behaviour: the lead-rich film reduces the risk of galling when lubrication is marginal or interrupted.
Machinability: the lead phase breaks chips cleanly, so bearing bores, oil grooves and close-tolerance fits can be produced at high cutting rates.
Good thermal conductivity for a casting: heat generated at the sliding surface is carried away rather than concentrated at the contact.
Non-magnetic and dimensionally stable: useful in instruments, electrical machinery and equipment that must not influence magnetic fields.
Typical Applications
Sleeve bearings, plain bearings and bushings for pumps, fans and conveyors
Thrust washers, wear plates and guide blocks in general machinery
Bearing cages and sliding components in machine tools and agricultural equipment
Valve bushings, stuffing-box parts and low-speed sliding contacts in process plant
Gear and worm-wheel blanks that will be fitted with a hardened mating surface
General engineering castings where a combination of wear resistance and easy machining is wanted
Two service conditions deserve caution. C91300 is not the alloy of choice for continuous high-velocity seawater duty, where cupronickel or nickel-aluminium bronze is normally specified because of the lead content. In markets where lead-bearing alloys are restricted, a lead-free bearing bronze should be substituted, and the drawing should state the service medium so that the material decision is made explicitly.
Specifying and Ordering C91300
An order that will be met correctly first time normally contains the UNS number, the casting standard and process, the purchased form and dimensions, the machining allowance if the part is to be machined from bar, the quantity, and the certification required for chemistry and mechanical properties. Where the finished part is a bearing, it also helps to state the shaft material, the load and speed of the application and the lubricant, because the same alloy performs very differently as a lightly loaded bushing and as a heavily loaded slow-speed bearing. Purchasers should also decide in advance whether the parts will be machined from continuous cast bar or supplied as castings to drawing, since that choice determines the tolerances, the surface condition and the inspection method that will be applied.
Frequently Asked Questions
Q: Is C91300 an aluminium bronze?
No. C91300 is a leaded tin bronze, in which tin and lead are the deliberate additions. Aluminium bronzes contain roughly nine to eleven per cent aluminium, for example the cast grades C95400 and C95800, and they are different alloys with different applications.
Q: Is C91300 a wrought or a cast alloy?
It is a cast alloy, which is why its UNS number begins with C9. It is normally supplied as continuous cast bar or hollow bar, or as sand castings to drawing, and it should not be ordered as a substitute for wrought brass or cupronickel products.
Q: Why does C91300 contain lead?
Lead is added deliberately. It improves machinability by breaking chips, and it forms a soft low-friction film at the sliding surface that helps the bearing survive marginal lubrication and small amounts of abrasive contamination.
Q: Can C91300 be welded?
Fusion welding of leaded tin bronze castings is generally not recommended, because the lead phase makes sound welds difficult and can cause porosity. Mechanical fastening, brazing or redesign of the joint is the better route.
Q: Can C91300 be used in seawater?
It will resist mildly corrosive water, but it is not the preferred grade for high-velocity seawater or continuous immersion duty. For pumps, valves and impellers in seawater, a cupronickel or a nickel-aluminium bronze such as C95800 is normally selected.
Q: Which standards cover C91300 castings?
Continuous cast product is covered by the ASTM B505/B505M series and sand castings by the ASTM B584 series for copper alloy castings. The applicable standard should always be stated on the order together with the UNS number.




