Aug 28, 2025 Leave a message

C61400 Aluminum Bronze: Hot and Cold Workability Explained

C61400 Aluminum Bronze and Its Working Characteristics

C61400 is a wrought aluminum bronze: copper alloyed with aluminium and iron, not a brass. That distinction matters because aluminium bronzes behave quite differently from copper-zinc alloys. The aluminium content builds a tough, adherent oxide film on the surface, and the iron addition refines the microstructure so the alloy can be hot worked and cold worked without losing toughness. The practical result is a material that can be forged, extruded, rolled and drawn while retaining excellent resistance to corrosion, erosion and cavitation.

Because the alloy tolerates both hot and cold deformation, one heat of C61400 can be converted into bar, tube, plate, strip and wire. That flexibility is why the grade appears across marine piping, seawater valves, heat exchanger components, pump parts and general process equipment rather than in a single narrow application.

Nominal Composition

Nominal values for the wrought alloy are listed below in weight percent. Copper forms the balance of the alloy.

Element Nominal content (wt %) Function
Copper Balance (about 88) Base metal; provides conductivity and film formation
Aluminium 6.0 - 8.0 Strengthening element; forms the protective oxide film
Iron 1.5 - 3.5 Grain refiner; improves strength and hot workability
Manganese 1.0 max Residual; assists deoxidation
Nickel 1.0 max (including cobalt) Residual; tolerated within the specification limit

C61400 is frequently confused with high-aluminium manganese grades such as CuAl9Mn2. Those are separate alloys with a higher aluminium level and a deliberate manganese addition, and they are covered by their own specifications. The two families should not be interchanged on a drawing without a fresh review of strength, corrosion and welding requirements.

Standard Designations by Product Form

Product form Typical designation Scope
Rod and bar ASTM B150/B150M Aluminium bronze rod, bar and shapes
Plate, sheet and rolled bar ASTM B171/B171M Copper-alloy plate and sheet for pressure service
Seamless tube ASTM B111/B111M Condenser, evaporator and heat exchanger tube
Forgings EN 12420 Copper and copper alloy forgings
Rod for general purposes EN 12163 Copper and copper alloy rod

Mechanical values are strongly temper dependent, so specification minima should be taken from the current edition of the relevant product standard rather than from general alloy data. For pressure-retaining parts, the allowable stress is set by the design code that governs the vessel or piping system, and the material certificate must match the form and temper actually supplied.

Hot and Cold Workability

The most quoted property of C61400 is its workability, and it deserves the attention it receives. Aluminium bronzes with higher aluminium levels tend to be hot short and difficult to roll; the iron addition in C61400 widens the safe hot working window and keeps the cast structure fine enough to accept deformation. In practice this means the alloy can be processed by the full range of conventional mill routes:

Hot forging of valve bodies, pump components and flanges.

Hot extrusion of solid bar and hollow sections.

Hot and cold rolling of plate, sheet and strip.

Cold drawing of tube and wire to finished dimensions.

Cold work increases strength and reduces ductility, which is normal for a copper alloy. When a component needs tight radii or deep forming, an inter-anneal should be scheduled into the route. Machining is satisfactory for a bronze of this type, and welding is achievable with processes appropriate to aluminium bronze, including procedures that use a matching filler and a preheat appropriate to the section thickness.

Corrosion and Mechanical Behaviour

The corrosion behaviour of C61400 is dominated by the aluminium-rich surface film. When the film is intact, the alloy resists seawater, brackish water, most neutral salt solutions and many industrial atmospheres. It also withstands the mechanical forms of attack that destroy weaker copper alloys: high-velocity seawater, entrained sand, and the collapsing bubbles of cavitation found downstream of pumps and valves. Under sustained high-velocity flow the film can be disturbed at edges and sudden contractions, so geometry is part of the corrosion design, not just material selection.

Strength is a function of temper. Cold worked bar and tube sit at the upper end of the range for the alloy, while annealed material is softer and more formable. Where a shaft, a valve stem or a pump bush must carry load, the wrought and cold worked condition is the normal choice; where the part must be bent or flanged in the workshop, a softer temper will save cost and avoid cracking.

Applications in Marine and Process Service

Seawater piping, fittings and valves, including components that see continuous flow.

Condenser and heat exchanger tubing and tube plates in power and desalination plants.

Pump bodies, impellers, wear rings and bushes exposed to abrasive slurries.

Marine composite plate and shipboard hardware where welding and corrosion resistance are both required.

Corrosion-resistant vessels, mechanical parts and structural fasteners in chemical and process plants.

The grade also sees use in fresh water and in mildly acidic process streams, provided temperature and chloride level stay inside the range for which the alloy was selected. Above that range, a higher-alloy bronze or a nickel-based alternative is the more economical answer over the life of the plant.

FAQ

Q: Is C61400 a brass or a bronze?
C61400 is an aluminum bronze. Brass is a copper-zinc alloy, while this grade is copper alloyed mainly with aluminium and iron, which is why it behaves differently in hot working, welding and corrosion.

Q: Why is C61400 described as easy to hot and cold work?
The iron addition refines the cast grain structure and widens the safe hot working range. That allows forging, extrusion, rolling and drawing, and it also gives the alloy enough room-temperature ductility for cold drawing of tube and wire.

Q: How does C61400 resist seawater?
Aluminium in the alloy forms a dense, self-repairing oxide film. The film protects the metal against general corrosion and, because it is tough, it also limits erosion and cavitation damage in high-velocity seawater systems.

Q: Can C61400 be welded?
Yes, with procedures suited to aluminium bronze and a filler that matches the parent metal. Weldability is good for a bronze of this class, but heat input and interpass temperature still need to be controlled on thick sections.

Q: Which forms of C61400 are available?
The alloy is produced as bar, rod, plate, sheet, strip, seamless tube and wire. Each form is covered by its own product standard and is supplied in a temper matched to the intended manufacturing route.

Q: How should C61400 be specified on a purchase order?
State the UNS number, the product form, the temper, the governing product standard and the required inspection. Adding the end application helps the mill confirm that the form and temper on offer suit the service.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry