Aug 28, 2025 Leave a message

C61400 Aluminum Bronze Bar and Tube Performance Analysis

Overview of the Grade

C61400 aluminum bronze is produced as bar and as seamless tube from the same alloy family, which allows an assembly such as a heat exchanger or a pump to be built without the galvanic mismatch that follows when dissimilar alloys are placed in contact. Aluminum at 6.0 to 8.5 percent with iron at 1.5 to 3.5 percent and the balance copper gives the grade its characteristic combination of strength, wear resistance and seawater corrosion resistance.

Bar and tube are not interchangeable in service, however. Bar is generally supplied in a wrought, extruded or drawn condition and is machined into bushes, valve parts and structural components, while tube is drawn to a specified wall with controlled concentricity so that it can be rolled into a tube sheet or bent into a coil. Performance assessment therefore has to be read together with the product standard that governs the item.

Chemical Composition of C61400

Element Symbol Minimum Maximum Note
Copper Cu Balance Remainder Matrix
Aluminum Al 6.0 8.5 Principal alloying element
Iron Fe 1.5 3.5 Strength and wear resistance
Nickel Ni - 0.6 Optional, improves corrosion resistance
Manganese Mn - 1.0 Optional, aids deoxidation
Zinc Zn - 0.50 Impurity
Lead Pb - 0.02 Impurity
Tin Sn - 0.20 Impurity
Silicon Si - 0.10 Impurity
Others - - 0.50 Total other impurities

All values are percentages by mass. Chemical composition alone does not define the delivered product: the mechanical requirements are set for the ordered temper, so the tube or bar is ordered with both a composition and a temper designation, and the certificate reports the measured results against those limits.

Performance of C61400 Bar

Wrought bar in this grade is characterised by good through-section soundness and a uniform, fine grained structure that machines cleanly and takes a fine surface finish. Because the alloy hardens rapidly under cold work, bar for heavily machined parts is normally ordered in a soft or lightly worked temper, and machining is planned so that the finishing cuts are taken after any stress relief operation rather than before it.

In service the bar form is used for bushes, wear rings, valve stems and bodies, pump components and structural fittings. Its strength makes it suitable for load bearing contact, and its aluminium oxide film protects it where sea water, condensate or mildly acidic process liquor is present. Where bar is machined across the section, attention should be paid to surface finish and to residual stress, since a coarse finish or a heavily cold worked surface layer will corrode more readily than the bulk of the material.

Performance of C61400 Tube

Seamless tube from the same alloy combines high strength with ductility, and this balance is what allows tubes to be expanded into a tube sheet or bent to a tight radius without cracking. The dense, homogeneous microstructure supports consistent mechanical properties through the wall, and the material keeps its strength and corrosion resistance at low temperatures as well as at ambient, which extends its use to refrigeration, polar and deep water applications.

Corrosion performance in tube is governed mainly by the condition of the internal surface and by flow. Clean, moderately fast flow maintains a stable protective film, while stagnant conditions allow deposits to settle and induce under-deposit attack; excessive velocity or entrained solids strip the film mechanically and expose fresh metal to erosion corrosion. Tube should therefore be specified with the correct wall thickness for the intended velocity and cleaned by methods that do not score the bore.

Product Forms, Standards and Size Range

Item Bar Tube
Product standard ASTM B150/B150M for rod, bar and shapes ASTM B111/B111M for seamless condenser tube
Equivalent code standard ASME SB150 ASME SB111
Size range Diameter 1 mm to 800 mm, round, square, hexagonal or flat Outside diameter 2 mm to 914 mm with wall 0.2 mm to 120 mm
Length 1 m, 2 m, 5.8 m, 6 m or cut to order Straight lengths or coils to order
Typical temper Soft to half hard Soft annealed or lightly drawn

Processing and Inspection Points

C61400 can be cast, forged, hot rolled, extruded and cold drawn, which is why bar and tube are made from the same heat without difficulty. Hot working is performed in the recommended high temperature range for aluminum bronze followed by controlled cooling, and cold reductions are separated by annealing. Joining is by brazing, soldering or gas-shielded arc welding, with low heat input and clean, dry joint preparation.

Inspection of tube covers pressure tightness and an electric non-destructive test as required by the product standard, plus dimensional checks on outside diameter, wall thickness and length; bar is checked for dimensions, straightness and surface condition. Chemical analysis and tension testing confirm the grade and temper, and the documentation can be issued to EN 10204 type 3.1 for export contracts. Material is protected with anti-rust treatment and packed in wrapped, strapped bundles on wooden pallets for sea transport.

FAQ

Q: Can C61400 bar and tube be used in the same assembly?
Yes. Because both are produced from the same alloy, using bar for the tube sheet and fittings and tube for the heat transfer surface avoids galvanic mismatch inside the exchanger.

Q: What is the aluminum and iron content of C61400?
Aluminum is specified at 6.0 to 8.5 percent and iron at 1.5 to 3.5 percent, with copper as the balance and tight limits on zinc, lead, tin and silicon.

Q: Which standard applies to C61400 bar?
ASTM B150/B150M covers aluminum bronze rod, bar and shapes, with ASME SB150 used where components are built to the ASME code.

Q: How does tube normally fail in seawater service?
Typically through under-deposit corrosion in stagnant zones or erosion corrosion where velocity and entrained solids are excessive, rather than through uniform metal loss.

Q: Does C61400 lose toughness at low temperature?
No. The alloy keeps useful strength and toughness at low ambient and cryogenic service temperatures, which is one reason it is used in refrigeration and cold climate installations.

Q: What documentation accompanies the material?
Chemical analysis, mechanical test results, dimensional inspection and the required pressure or non-destructive test results are issued on the mill certificate, which can be provided to EN 10204 type 3.1.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry