Oct 30, 2025 Leave a message

C23000 Red Brass Water Pipe and 3/8 in. Bendable Copper Tube

Red Brass Water Pipe and the 3/8 in. Bendable Tube

Two product forms of the same alloy dominate small water systems. Thick wall red brass pipe is used for rigid runs, risers and threaded connections; 3/8 in. bendable copper tube is used where a line must follow a structure, pass around obstructions or be coiled for delivery. Both are made from C23000, the 85 % copper and 15 % zinc red brass that is among the most durable of the commercial water pipe metals.

Red brass earns that reputation from its single-phase structure. It resists dezincification, seasonal cracking and pitting corrosion in water service, it can be thermoformed, and it accepts both welded and brazed joints. Its warm natural colour also makes it a common choice for exposed architectural and outdoor work.

Chemical Composition

Element Cu Zn Pb Fe Other elements
Weight % 84.0 - 86.0 Remainder 0.05 max 0.05 max 0.10 max

The narrow copper window and low lead content are the reason the alloy behaves predictably in drinking water and in mildly aggressive soils. Copper plus named elements must total at least 99.8 %.

Physical and Mechanical Properties

Property Typical value
Density 8.7 - 8.8 g/cm³
Melting range (solidus to liquidus) approx. 970 - 1030 °C
Electrical conductivity (annealed) 28 - 32 % IACS
Thermal conductivity at 20 °C approx. 120 W/(m·K)
Modulus of elasticity in tension approx. 110 - 117 GPa
Machinability rating (free-cutting copper = 100) 30
Temper Tensile strength Yield strength Elongation
Annealed, O61 280 - 345 MPa 95 - 150 MPa 40 % min
Half hard, H02 380 - 430 MPa 280 - 350 MPa 20 % min
Hard, H04 450 - 520 MPa 380 - 450 MPa 8 - 15 %

Bendable tube is supplied annealed because the full elongation range is needed for tight radii. Pipe for threaded risers is normally supplied half hard or hard so that the wall resists deformation in service.

Bending Practice for 3/8 in. Tube

Nominal outside diameter 9.5 mm, with wall thickness selected for the working pressure of the system

Cold bending on annealed tube gives the smoothest result for radii above roughly three times the outside diameter

Tighter radii are formed with a mandrel or by hot forming at about 700 - 800 °C, followed by controlled cooling

A small allowance is made for springback; tube is normally released slightly past the required angle

Annealing in the range 450 - 600 °C restores ductility if a run needs several successive bends

Bends should not be made closer to a brazed joint than the length needed to keep the joint cool during fabrication

Tube cutters and benders designed for copper alloys should be used, since red brass work-hardens and a scored or nicked outer surface becomes a stress raiser. For pipe, threads are cut with sharp, lubricated dies and the wall schedule is chosen so that ample wall remains under the thread root.

Water Service Applications

Potable water supply, distribution and riser lines in residential and commercial buildings

Conduit and protective runs for cable and instrumentation

Architectural exposed pipework, rainwater goods and decorative metalwork

Pipe nipples, fittings blanks and threaded couplings

Cooling water, pump lines and general industrial water circuits

Outdoor and irrigation installations where corrosion resistance and appearance both matter

Water chemistry still governs service life. Where the supply is aggressive, the wall thickness should include a corrosion allowance, and dead legs or stagnant aerated pockets should be avoided because they concentrate attack on any brass surface.

Joining and Installation

Soldering and brazing are the preferred methods and both perform well on this alloy. Gas shielded arc welding is workable, butt welding is acceptable, and spot welding is only fair; coated metal arc welding and seam welding are not recommended because the zinc in the alloy vaporises under heavy heat input. Mechanical joints using compression or flared fittings are widely used on 3/8 in. tube and avoid heat entirely.

Every run should be flushed and pressure tested before handover, and tubing stored on site should remain capped to keep the bore clean and dry.

FAQ

Q: Is 3/8 in. red brass tube suitable for drinking water?
Yes. C23000 with the low lead content specified for the alloy is used in potable water lines, and it resists the dezincification and pitting that shorten the life of lower-grade brasses.

Q: How tight a bend can be made in annealed tube?
Radii of roughly three times the outside diameter are practical for cold bending on annealed stock. Anything tighter calls for mandrel bending or hot forming in the 700 - 800 °C region.

Q: Should pipe or tube be chosen for a water riser?
Use pipe where the run is rigid, threaded and pressure rated, and use bendable tube where the line must follow building geometry or be delivered in coils. Both are available in the same alloy.

Q: What causes brass pipe to fail prematurely in water service?
Stagnant aerated water, deposits that create under-deposit attack and insufficient wall allowance are the common causes. Correct sizing, flushing and avoiding dead legs protect the alloy.

Q: Which standards apply to water pipe and tube in this alloy?
Seamless red brass pipe is ordered to ASTM B43, seamless brass tube to ASTM B135 and welded brass tube to ASTM B587, with copper water tube practice covered by ASTM B88 and EN 1057 for the pure copper grades.

Q: Can the tube be joined without heat?
Yes. Compression and flared fittings rated for the tube diameter and pressure allow mechanical joints, which is useful where a torch cannot be used safely.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry