Mar 27, 2025 Leave a message

C17500 Copper-Cobalt-Beryllium Alloy: High-Conductivity Age-Hardened Copper for Connectors and Welding Equipment

C17500 is the copper-cobalt-beryllium (CuCoBe) alloy, an age-hardenable copper that sits between the very strong, low-conductivity beryllium coppers and the very conductive, lower-strength precipitation-hardened coppers such as chromium-zirconium copper. It contains less beryllium than the 1.9% beryllium grades, and the cobalt addition controls the precipitate so that strength and conductivity are obtained together.

Composition and Strengthening Mechanism

The beryllium content is deliberately restricted to 0.40-0.70%. Because that is well below the 1.80-2.00% level of the high-strength beryllium coppers, very little solute is left in solution after ageing, and the residual solute has only a small effect on electron scattering. The result is the high conductivity for which the grade is specified. Cobalt, at 2.40-2.70%, refines the precipitate and controls the hardening response, and the alloy is also supplied in cobalt-free or cobalt-substituted variants within the same family where required.

Element Specified range Function
Beryllium 0.40-0.70% Precipitation hardening with minimum loss of conductivity
Cobalt 2.40-2.70% Controls precipitate size and distribution
Copper Balance Matrix
Impurities Individually controlled Protect conductivity and hot workability

Rod and bar are covered by ASTM B441 and plate, sheet, strip and rolled bar by ASTM B534.

Properties by Temper

Condition Tensile strength Hardness Conductivity Comment
Solution annealed 400-600 MPa about 60 HRB about 20-25% IACS Soft condition for forming
Age hardened (TM00 / TH02) 690-900 MPa 20-30 HRC 45-55% IACS Normal service condition

These are typical commercial values; the minimum values that apply to a purchase are fixed by the product standard for the temper and form ordered.

Heat Treatment

Solution treatment: approximately 900-950 deg C, followed by a water quench. The high solution temperature is needed to take the cobalt and beryllium into solid solution.

Age hardening: approximately 460-500 deg C for two to four hours. This is the stage at which strength rises and conductivity recovers to the 45-55% IACS band.

Forming sequence: cold form and machine the parts in the solution-treated condition, then age harden to final properties. Only light corrective work should follow ageing.

Brazing and joining: brazing is normally carried out before the ageing treatment, or with a filler whose melting range is compatible with the ageing temperature.

Over-ageing: exceeding the ageing temperature or time coarsens the precipitate, reducing strength without any compensating gain in conductivity.

How C17500 Compares with Other Hardened Coppers

The selection ladder for hardened copper is straightforward. Where maximum strength is needed, the 1.9% beryllium coppers deliver roughly 1100-1300 MPa but hold conductivity to about 20-28% IACS. Where conductivity is paramount and softening temperature is the critical property, chromium-zirconium copper delivers about 80% IACS and resists softening to roughly 525 deg C, but at a lower strength level. C17500 occupies the middle ground at 690-900 MPa with 45-55% IACS, and it adds good resistance to stress relaxation at moderately elevated temperature, so current-carrying parts keep their contact force in service.

Applications

Resistance-welding equipment is the classic application: electrode holders, seam-welding wheels, back-up bars and fixtures that must carry heavy current while staying hard and cool. The alloy is also used for electrical switchgear and contact parts, fuse clips, current-carrying springs and terminals, power-electronics connectors and busbars, heat sinks that also carry structural load, non-magnetic instrument components and precision parts in aerospace and industrial equipment.

Processing and Quality Control

Machining: the alloy machines well in the solution-treated condition, with sharp positive-rake tooling and good chip control. Parts are usually finish machined before ageing, because hardness rises in the ageing step.

Forming: high conductivity tempers such as this one need generous bend radii compared with pure copper, because strength and limited ductility are traded for conductivity.

Welding: fusion welding is not recommended for copper-beryllium alloys. Brazing and mechanical joints are the preferred methods of assembly.

Hygiene: beryllium-bearing dust must be controlled with extraction and wet methods at every machining and grinding step.

Verification: spectrometric chemistry, hardness testing and a conductivity test are the practical way to confirm that the ageing treatment has been carried out correctly, since hardness and conductivity together define the delivered condition.

FAQ

Q: What conductivity does C17500 reach?
Roughly 45-55% IACS in the age-hardened condition, which is about twice the conductivity of the 1.9% beryllium coppers and about half that of chromium-zirconium copper.

Q: How is C17500 hardened?
Solution treatment at approximately 900-950 deg C with a water quench, then age hardening at approximately 460-500 deg C for two to four hours.

Q: Is C17500 better than C17200 for welding electrodes?
It depends on the duty. C17500 is preferred where high current and low electrical loss dominate; the higher-strength beryllium coppers are chosen where mechanical load and tip hardness dominate. Both are used in resistance-welding equipment.

Q: Is the alloy magnetic?
No. It is non-magnetic and is therefore suitable for instrument and electrical parts where magnetic interference must be avoided.

Q: Which standards cover the product forms?
Rod and bar are specified to ASTM B441 and plate, sheet, strip and rolled bar to ASTM B534. Certificates state chemistry, temper and mechanical properties against those requirements.

Q: Can C17500 be welded?
Fusion welding is not recommended, mainly because of the beryllium content and the loss of properties in the weld zone. Brazing, soldering and mechanical fastening are the normal assembly methods.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry