Oct 24, 2025 Leave a message

C10100.pdf

C10100 Thin-Walled Round Copper Tube for Medical Gas Systems

Why Copper Is Used for Medical Gas Systems

A medical gas pipeline system delivers oxygen, medical air, nitrous oxide, carbon dioxide and vacuum from a plant room to the point of use at a ward or operating theatre. The tube must not react with the gas, must not shed particles or oil into the stream, must be capable of being joined in a way that is verifiably gas-tight, and must survive pressure cycling and cleaning. Copper satisfies all of these requirements, and it is the established material for medical gas and vacuum pipework in hospitals.

The thin-walled, round, seamless form is preferred because a thin wall equalises the surface finish along the bore, keeps the wall thin enough for reliable brazed joints and mechanically formed bends, and reduces the weight of large distribution headers. The grade specified for the highest-purity duties is C10100, the oxygen-free electronic copper.

C10100 Composition and Cleanliness Requirements

Oxygen-free copper is specified for medical gas service because oxygen reacts with copper oxide inclusions at brazing temperature, generating steam pockets that leave voids in the joint and loose oxide particles in the bore. Holding the oxygen content down removes that mechanism altogether.

Element Requirement
Copper (Cu) 99.99 % minimum
Oxygen (O) 0.001 % maximum
Individual impurities (Pb, Bi, Fe and others) Each typically 0.001 % maximum

In addition to chemistry, medical gas tube specifications impose a cleanliness limit: the bore must be free of drawing lubricant, scale, carbon and particulate, and the tube is normally supplied with the ends capped and the bore purged. The maximum total residual contamination and the method of test are laid down by the applicable medical gas standard and by the national health facility code that governs the installation.

Standard Designations for Medical Gas Tube

Three families of document matter to a medical gas tube buyer:

The product standard, which defines the alloy, the temper, the dimensions and the wall-thickness classes. In Europe this is EN 13348, covering seamless round copper tubes for medical gases or vacuum, with the wall classes commonly referenced as Table X (light gauge half-hard), Table Y (annealed half-hard) and Table Z (hard-drawn thin wall). In the United States, ASTM B819 is the equivalent product specification for seamless copper tube for medical gas systems.

The system standard, which defines how the pipeline is designed, brazed, purged, tested and documented. ISO 7396-1 covers medical gas pipeline systems, and in the United States NFPA 99 governs health care facilities including medical gas and vacuum systems.

The general copper product standards, such as ASTM B75 and ASTM B88, which define the Seamless copper tube, Types K, L and M used for the heavier-walled portions of the circuit.

Because the wall classes are defined by the product standard, the correct practice is to state both the alloy and the wall class on the purchase order - for example C10100 in the Table Z hard-drawn thin-wall condition - rather than an arbitrary wall thickness.

Dimensions and the Type K, L and M Relationship

Heavier-walled medical gas and general service tube follows the familiar Type K, L and M system, in which the outside diameter is common to all three types and the wall thickness, and therefore the bore, changes with the type. Type K has the heaviest wall, Type L the intermediate wall and Type M the lightest. The table below gives representative values for the smaller sizes; the full dimensional schedule is set out in the product standard.

Outside diameter mm (in) Nominal size in Type L bore mm (in) Type K bore mm (in) Type M bore mm (in)
9.5 (3/8) 1/4 8.001 (0.315) 7.747 (0.305) -
12.7 (1/2) 3/8 10.922 (0.430) 10.211 (0.402) 11.430 (0.450)
15.875 (5/8) 1/2 13.843 (0.545) 13.411 (0.528) 14.453 (0.569)
19.05 (3/4) 5/8 16.967 (0.668) 16.561 (0.652) 17.526 (0.690)
22.225 (7/8) 3/4 19.939 (0.785) 18.923 (0.745) 20.599 (0.811)
28.575 (1 1/8) 1 26.035 (1.025) 25.273 (0.995) 26.797 (1.055)
34.925 (1 3/8) 1 1/4 32.131 (1.265) 31.623 (1.245) 32.791 (1.291)
41.275 (1 5/8) 1 1/2 38.227 (1.505) 37.617 (1.481) 38.786 (1.527)
53.975 (2 1/8) 2 50.419 (1.985) 49.759 (1.959) 51.029 (2.009)
66.675 (2 5/8) 2 1/2 62.611 (2.465) 61.849 (2.435) 63.373 (2.495)
79.375 (3 1/8) 3 74.803 (2.945) 73.838 (2.907) 75.717 (2.981)

For the thin-walled medical gas classes, the standard pairs each outside diameter with a specific wall thickness for each class and publishes the corresponding maximum working pressure. Working pressure falls as the wall thins and as the outside diameter rises; the values must be taken from the standard's own table for the class actually purchased, because a nominal wall thickness alone does not define the pressure rating.

Pressure Rating, Temper and Bending

Medical gas systems operate at modest pressures - the distribution pressure downstream of the terminal unit regulator is far below the burst capability of the tube - so the practical drivers of wall selection are bendability, joint quality and mechanical robustness during installation rather than internal pressure alone. Vacuum service reverses the loading direction, but the tube wall is sized for external pressure and for rigidity in that case.

Temper selection follows the same logic. The annealed half-hard class bends easily on site and is used where the route involves many changes of direction. The hard-drawn thin-wall class holds its shape in straight runs, is stiffer and has a smoother bore, but requires a larger minimum bend radius. Hard-drawn tube should not be annealed on site, because the resulting oxide and scale would have to be removed from the bore before the system could be accepted.

Installation, Brazing and Acceptance Testing

Medical gas pipework is joined almost exclusively by brazing with a filler that does not contain cadmium, using a nitrogen purge through the bore during the operation. The purge is not optional: without it, copper oxide forms on the inside surface of the joint, and that oxide is exactly the contamination the oxygen-free grade was chosen to prevent. Additional requirements that apply to a compliant installation are:

Cutting and preparation with dedicated tooling used only for medical gas work, so that oil and particulate from other trades cannot enter the bore.

Brazing by qualified operatives working to a documented procedure, with joints purged until they cool.

Pressure and tightness testing, followed by a cross-connection test to verify that each terminal delivers the correct gas.

Purity testing of the delivered gas at the terminal outlet, with the results recorded.

Cleanliness verification before the system is handed over.

Tube should be stored with caps in place and cut ends re-capped immediately, because a contaminated bore cannot be cleaned effectively after installation.

FAQ

Q: Why is oxygen-free copper used for medical gas systems?
Because the absence of oxygen prevents the steam pockets and internal oxide that form during brazing of ordinary copper, so the joints stay sound and the gas stream stays clean.

Q: Which standard covers medical gas copper tube?
EN 13348 covers seamless round copper tubes for medical gases or vacuum in Europe, and ASTM B819 is the equivalent product specification in the United States. Installation is governed by ISO 7396-1 and by national facility codes.

Q: What are Table X, Table Y and Table Z in EN 13348?
They are the three wall-thickness and temper classes of the standard: Table X for light-gauge half-hard tube, Table Y for annealed half-hard tube and Table Z for hard-drawn thin-wall tube. Each class has its own dimensional and working pressure schedule.

Q: Can ordinary plumbing copper tube be used for medical gas?
No. Medical gas tube must meet the cleanliness, alloy and temper requirements of the medical gas product standard, and the installation must be brazed under nitrogen purge and verified by purity testing.

Q: What is the difference between Type K, L and M copper tube?
The outside diameter is the same for all three types, but Type K has the heaviest wall, Type L an intermediate wall and Type M the lightest, so the bore and the pressure rating differ.

Q: How should medical gas tube be stored and handled?
Keep the tube indoors and dry with the ends capped, use dedicated cutting and bending tools, and re-cap any cut end immediately to keep the bore free of oil, dust and moisture.

Summary

C10100 thin-walled round copper tube gives medical gas and vacuum systems the inert bore, clean brazed joints and predictable mechanical behaviour that hospital installations require. Order the alloy together with the correct wall class and temper from the product standard, keep the bore capped and clean at every stage, and carry out the purge, pressure test and cross-connection test that the system standard demands.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry