ASTM B111 and the C44300 Admiralty Brass Grade
ASTM B111 is the specification for seamless copper and copper alloy tube for condensers, evaporators and heat exchangers. UNS C44300 is the admiralty brass grade within that family: a copper-zinc-tin alloy containing about 70 % copper, 28 % zinc and 1 % tin, with a small arsenic addition that suppresses dezincification. The matching ASME SB111 document is used for pressure equipment.
Admiralty brass sits between plain brass and the copper-nickel alloys. It offers higher strength and better erosion resistance than soft brass, better thermal conductivity than cupronickel, and a price that suits large condenser bundles operating on fresh water, cooling tower water and brackish water. It is the classic material for steam surface condensers and for the water boxes of industrial heat exchangers.
Chemical Composition
| Element | Requirement, % |
|---|---|
| Copper | 70.0 - 73.0 |
| Zinc | Remainder, nominally 27 - 29 |
| Tin | 0.9 - 1.2 |
| Arsenic | 0.02 - 0.06, added to inhibit dezincification |
| Iron | 0.06 max |
| Lead | 0.07 max |
The tin and arsenic additions are what separate admiralty brass from ordinary 70/30 brass. Tin improves resistance to impingement and to dezincification, while arsenic acts as a cathodic inhibitor that keeps the zinc in solution rather than allowing it to be leached out of the metal. Iron and lead are held to low ceilings so that the tube remains sound and formable.
Mechanical and Physical Properties
| Property | Value, annealed condition |
|---|---|
| Tensile strength | 310 - 450 MPa |
| Yield strength, 0.5 % extension | about 125 MPa |
| Elongation in 50 mm | 30 % min |
| Hardness | about 65 HRB |
| Density | about 8.53 g/cm³ |
| Thermal conductivity | about 110 W/(m·K) |
Tube is normally supplied in the annealed temper designation O61 for straight lengths, and in a light drawn or U-bent condition where the bundle is to be installed as a finished assembly. The annealed temper expands reliably into tubesheets and tolerates the small amount of cold work imposed by roller expansion.
Size Range and Supply Condition
| Parameter | Range |
|---|---|
| Outside diameter | 6 mm to 80 mm |
| Wall thickness | 0.7 mm to 3.5 mm |
| Lengths | Straight lengths up to about 12 m, or cut to condenser drawing |
| U-bend option | U-bent bundles with matched leg lengths and bend radii |
| Temper | Annealed O61 as standard, other tempers by agreement |
Bundles are normally supplied with the tube ends finished for the tube sheet hole and with the bends free of ovality and wrinkles. Tubes are packed in wooden cases with the bores protected, because a damaged bore is the starting point for localised corrosion in service.
Condenser, Desalination and Heat Exchanger Applications
Steam surface condensers in power stations and industrial plants.
Process and utility heat exchangers on cooling tower or river water.
Evaporators, distillers and water heaters.
Marine and offshore cooling systems on fresh water and brackish circuits.
Oil coolers, aftercoolers and lube oil heat exchangers.
Desalination plant preheaters and condensers where chloride levels are moderate.
In service the alloy forms a protective surface film that is continuously renewed, and the tin content helps the film withstand the turbulent flow at the inlet end of the tube, the point where most impingement failures begin. For full seawater duty at high velocity, the copper-nickel grades such as C70600 and C71500 remain the safer choice, and admiralty brass is best reserved for fresh, brackish or moderately aggressive cooling water.
Corrosion Behaviour and Design Velocities
Admiralty brass resists fresh water, brackish water and polluted river water well, and the arsenic addition gives it good resistance to dezincification in most waters. It is not suitable for ammonia-bearing condensate, for waters with high free chlorine residuals, or for services carrying suspended abrasives. Design velocities in clean seawater are normally limited to about 1.5 m/s and are set lower where the water carries sand, while velocities that are too low allow deposits to settle and cause under-deposit attack. Cathodic protection in the water box and correct baffle clearances both help to prolong tube life.
Fabrication, Installation and Inspection
Tube is expanded into tubesheets with a roller expander, or rolled and then seal welded where a fully leak-tight joint is required. U-bends are formed on a mandrel and, where the bend radius is tight, a stress relief anneal follows to remove the cold work that would otherwise make the bend sensitive to stress-corrosion cracking. Soldering and brazing are used for small connections, and silver-bearing filler metals are preferred where the joint will see elevated temperature. Cleaning after fabrication must remove all traces of flux, oil and swarf.
Finished tube is examined for dimensions, wall thickness, surface finish and internal soundness, with eddy current testing standard for condenser bundles, pneumatic or hydrostatic testing used to prove tightness, and tensile and hardness testing used to confirm the temper. A mill test certificate to EN 10204 3.1 accompanies each heat, and third party inspection is offered for power station and shipyard contracts.
FAQ
Q: What makes admiralty brass different from ordinary brass?
The tin addition improves resistance to erosion and dezincification, and the arsenic addition inhibits the selective leaching of zinc. Together they make C44300 far more durable than a plain 70/30 brass in cooling water service.
Q: Is C44300 suitable for seawater?
It is suitable for brackish and mildly aggressive seawater at controlled velocity. For high velocity or heavily aerated seawater, the copper-nickel grades C70600 and C71500 are the recommended materials.
Q: What velocity limit applies in clean seawater?
Design velocities are generally held to about 1.5 m/s and reduced where the water carries sand or entrained air. A minimum velocity is also applied to avoid deposits settling on the tube wall.
Q: How are brass tubes joined to a tubesheet?
They are roller expanded into the tube holes, with or without seal welding. Expansion is controlled to avoid over-rolling, which can leave residual tensile stress and shorten tube life.
Q: Why does the specification include arsenic?
Arsenic is a deliberate inhibitor addition that prevents dezincification, the selective corrosion of the zinc phase that would otherwise perforate brass tube in aggressive water.
Q: What testing is supplied with a condenser bundle?
Dimensional and wall thickness verification, tensile and hardness results, eddy current examination of the full length, hydrostatic or pneumatic tightness testing and a mill test certificate to EN 10204 3.1 issued by heat number.




