Oct 27, 2025 Leave a message

C70600-Copper-Nickel-Size.pdf

ASTM B111 C70600 90/10 Copper-Nickel Hollow Thin Wall Pipes

ASTM B111 C70600 hollow thin wall pipes are the small-wall section of the 90/10 copper-nickel family, drawn to outside diameters and wall thicknesses that keep weight low while retaining the seawater resistance of the alloy. With 9–11% nickel, iron and manganese additions and a copper content of 88.6% minimum, the tube resists corrosion, erosion and biofouling in condensers, sea water pipework and hydraulic circuits.

What Makes Thin Wall C70600 Pipe Different

A thin wall section transfers heat with less metal in the path, so the same duty can be met with less material and lower tube weight. The drawn process keeps the wall concentric, which matters when the tube is roller expanded into a tubesheet: an eccentric wall expands unevenly and creates a leak path. Hollow thin wall pipes are therefore specified where a light bundle, a close tube pitch or a small heat exchanger envelope is required.

Low tube weight and reduced bundle mass

Concentric wall for reliable roller expansion

Dense tube pitch possible in compact exchangers

Retains full seawater corrosion resistance of 90/10 alloy

Chemical Composition of 90/10 Copper-Nickel

Element Content (%)
Nickel, Ni 9.0–11.0
Iron, Fe 1.0–1.8
Manganese, Mn 1.0 max
Zinc, Zn 1.0 max
Lead, Pb 0.05 max
Copper, Cu 88.6 min

Physical and Mechanical Properties

Property Value
Density 8.1 g/cm³
Melting point 1443 °C (2430 °F)
Tensile strength 551 MPa (80,000 psi)
Yield strength, 0.2% offset 241 MPa (35,000 psi)
Elongation 30%

Size Range and Schedules

Item Range
Outside diameter 1/8 in to 3 1/2 in
Wall thickness 0.012 in to 0.250 in
Common wall sections 0.028, 0.035, 0.049, 0.065, 0.083, 0.095, 0.109, 0.120, 0.125, 0.134 in
Schedule coverage SCH 5, 10, 40, 80, 120, 160 and XXH depending on nominal bore
Lengths Straight lengths and coils to order

Pipe sizes from 1/8 in IPS (0.405 in OD) through 3 in IPS (3.500 in OD) are available in the lighter schedules, while heavier schedules up to XXH are produced for the larger bores where wall thickness governs the pressure rating.

Equivalent Grade and Standards

Designation Reference
UNS C70600 90/10 copper-nickel
Werkstoff 2.0872 CuNi10Fe1Mn
ASTM B111 Seamless condenser tubes and ferrule stock
ASTM B466 / ASME SB466 Seamless copper-nickel pipe and tube

Applications of Thin Wall 90/10 Pipe

Condenser and heat exchanger tube bundles in ships and power plants

Sea water pipework, offshore fire water systems and deck services

Desalination units and evaporator circuits

Hydraulic lines and instrumentation tubing

Fish cages and aquaculture structures

Pumps, valves, sheathing and hull fittings

Inspection and Documentation

Thin wall tubes are released with test documentation that follows the order: EN 10204/3.1B inspection certificates, raw material certificates, a 100% radiography test report and third-party inspection reports where specified. Dimensional checks cover outside diameter, wall thickness, length and ovality, and the bore is inspected for drawing marks or inclusions before packing.

Frequently Asked Questions

Q: What is the difference between C70600 pipe and thin wall C70600 tube?
Both are the same 90/10 alloy. The thin wall section is drawn to a lighter wall, which reduces weight and allows a denser tube pitch in condensers and heat exchangers.

Q: What wall thicknesses are available?
Thin wall sizes run from 0.012 in upwards, with 0.028, 0.035, 0.049, 0.065, 0.083, 0.095, 0.109, 0.120 and 0.134 in being the sections most often ordered.

Q: What is the equivalent grade of C70600?
The alloy is known as 90/10 copper-nickel in UNS terms and as Werkstoff 2.0872, CuNi10Fe1Mn, in the German designation system.

Q: What strength does thin wall 90/10 pipe offer?
Tensile strength is 551 MPa (80,000 psi) with a 0.2% offset yield strength of 241 MPa (35,000 psi) and 30% elongation, with a density of 8.1 g/cm³.

Q: Which schedules can be supplied?
Depending on nominal bore, SCH 5 through SCH 160 and XXH are produced, covering pipe from 1/8 in IPS up to 18 in IPS in the heavier schedules.

Q: What documentation comes with the pipe?
EN 10204/3.1B inspection certificates, raw material certificates, a 100% radiography report and third-party inspection reports are issued as required by the order.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry