Thick wall tube to ASTM B111 in UNS C44300 is a heavy-gauge form of arsenical admiralty brass, a copper-zinc-tin alloy used where a condenser or heat exchanger must survive aggressive cooling water. The additional wall thickness is not merely a strength measure: it is a deliberate corrosion allowance that keeps the tube tight for a full maintenance interval even when the water side is erosive or mildly contaminated.
Admiralty brass has been the standard seawater tube material for a century because it resists dezincification, general corrosion and impingement attack while remaining far less costly than copper-nickel alloys. The small deliberate addition of arsenic acts as an inhibitor that suppresses preferential loss of zinc, and the tin content improves resistance to erosion and to attack in polluted water.
Material Definition and Applicable Standards
ASTM B111/B111M specifies seamless tube and ferrule stock of copper and copper alloys up to 3 1/8 in. (80 mm) inclusive in diameter for surface condensers, evaporators and heat exchangers. C44300 is the arsenical admiralty brass grade.
ASME SB111 carries identical requirements for pressure equipment, and EN 12451 covers the same family of seamless heat exchanger tubes in the European system.
The matching European composition designation is CuZn28Sn1As, a 28 % zinc admiralty brass with tin and arsenic additions.
GB/T 8890 and JIS H3300 provide the Chinese and Japanese equivalents for seamless copper alloy heat exchanger tubes.
Thick wall products are ordered in the annealed and drawn tempers of the specification; the heavier wall means the same alloy is available with a longer service life rather than a different metallurgy.
Chemical Composition of C44300 Admiralty Brass
| Element | Requirement | Effect |
|---|---|---|
| Cu | 70.0 - 73.0 % | Base metal, sets the corrosion potential |
| Sn | 0.9 - 1.2 % | Improves erosion and impingement resistance |
| As | 0.02 - 0.06 % | Inhibitor that prevents dezincification |
| Fe | 0.06 % max | Controlled to protect ductility |
| Pb | 0.07 % max | Kept low for hot formability and weldability |
| Zn | Remainder | Balances strength and thermal conductivity |
| Cu + named elements | 99.6 % min | Purity control of the specification |
Mechanical Properties, Physical Data and Dimensions
Minimum tensile strength in the annealed condition is about 310 MPa, and minimum yield strength at 0.5 % extension under load is about 105 MPa. Because the alloy is used in a heavy wall, the specified properties are normally achieved with comfortable margin.
Expansion of the tube outside diameter is required at 20 % of the original outside diameter, which demonstrates the ductility needed for rolling into tubesheets.
Annealed tube carries a nominal grain size requirement, commonly 0.025 mm or 0.015 mm depending on temper, verified metallographically.
Hardness, electrical conductivity and modulus values are reported per the physical property tables of the specification; thermal conductivity is lower than that of deoxidized copper, so heat transfer surface is sized accordingly.
Thick wall tube is ordered by outside diameter and wall thickness, with straight lengths, U-bends or ferrule stock available. Ovality, wall eccentricity and end preparation are controlled to suit expansion into a tubesheet.
Applications
Main and auxiliary surface condensers in steam power and marine plants cooled by seawater or estuarine water.
Multi-stage flash and multi-effect desalination plants, brine heaters and distillate coolers.
Shell and tube oil coolers, jacket water coolers and aftercoolers in diesel and gas engine installations.
Chemical plant condensers, evaporators and coolers handling brackish water or contaminated river water.
Ferrule stock and heavy wall tube used where the tube-to-tubesheet joint and the inlet length must resist erosion.
Selection, Fabrication and Installation Guidance
Choose a heavier wall for the inlet lengths and for units with high water velocity or sand content, and thinner walls where the water is clean and treated.
Roll thick wall tube into the tubesheet with a controlled expander so that wall reduction and tube-sheet ligament stress stay within the design joint; the heavier wall tolerates a wider expansion window than thin wall tube.
Use inhibited filler materials or low-temperature brazing methods that do not promote dezincification at the joint; do not overheat the tube end.
Provide cathodic protection or a sacrificial anode when brass tubes are fitted into steel water boxes, and keep brass and copper-nickel bundles electrically separated where mixed materials are unavoidable.
Stress relieve or select an annealed temper where ammonia or amine contamination is possible, because brasses are sensitive to stress corrosion cracking.
Inspection Points and Common Pitfalls
Verify the arsenic and tin contents on the mill certificate: admiralty brass without the arsenic inhibitor is far more prone to dezincification in seawater.
Confirm wall thickness by ultrasonic or destructive measurement at both ends, since a nominal heavy wall can be defeated by eccentricity in the drawn tube.
Check eddy current records for longitudinal and transverse defects, which are especially important in the thicker walls used for long-life seawater service.
Do not assume that a heavier wall allows unlimited water velocity; impingement attack at the tube inlet is still the most common failure mode and is normally solved with ferrules or inlet protection.
Keep the alloy within its temperature range and avoid long exposure to dry steam or high-ammonia condensate, where ammonia attack rather than seawater corrosion governs life.
FAQ
Q: What is the difference between admiralty brass and ordinary brass tube?
Admiralty brass C44300 contains tin and a controlled arsenic addition. The tin improves resistance to erosion and impingement, and the arsenic inhibits dezincification, which is the failure that limits plain brass in cooling water.
Q: When should thick wall C44300 be selected instead of thin wall tube?
Use a heavier wall for high water velocity, sandy or abrasive water, long maintenance intervals, or where the tube must tolerate repeated rolling. The extra metal acts as a corrosion allowance rather than as extra strength.
Q: What mechanical properties does ASTM B111 require for C44300?
In the annealed condition the specification requires a minimum tensile strength of approximately 310 MPa and a minimum yield strength of approximately 105 MPa at 0.5 % extension under load, together with a 20 % expansion test and controlled grain size.
Q: Is C44300 suitable for desalination service?
Yes. Admiralty brass is widely used in brine heaters, distillate coolers and multi-stage flash plant, provided water velocity, venting and deaeration are controlled so that ammonia and oxygen levels stay within design limits.
Q: How is thick wall admiralty brass tube supplied?
It is supplied as seamless straight lengths, U-bent tubes, and ferrule stock in the annealed or drawn tempers of ASTM B111, with outside diameter and wall thickness stated separately on the purchase order.
Q: What causes early failure of admiralty brass condenser tubes?
The usual causes are impingement at the inlet, deposit corrosion under sludge, ammonia-induced stress corrosion cracking and excessive residual stress from over-rolling. Correct water treatment, inlet protection and controlled expansion address most of them.




