What C10100 OFHC Conductor Tubing Is
C10100 is oxygen-free high-conductivity copper, OFHC, produced by converting selected refined cathodes and castings under closely controlled conditions so that contamination of the pure metal is avoided during every processing step. The copper content is 99.99%, and because the content of extraneous elements is so low, the inherent properties of elemental copper are available at a very high degree: ductility, electrical and thermal conductivity, impact strength and creep resistance are all at their best.
The tubing form is used as a conductor and as a vacuum envelope component. Typical duties include bus conductors, hollow conductors, coaxial cable and coaxial tube, klystron and microwave tube parts, anodes for vacuum tubes, lead-in wire, wave guides and glass-to-metal seals. In all of these the combination of purity, vacuum behaviour and formability decides whether the part works.
Composition Limits
| Element | Limit, % |
|---|---|
| Copper (Cu) | 99.99 min |
| Antimony (Sb) | 0.0004 |
| Arsenic (As) | 0.0005 |
| Oxygen (O) | 0.0005 |
| Phosphorus (P) | 0.0003 |
| Tellurium (Te) | 0.0002 |
These are the impurity limits applied to oxygen-free copper for electronic and vacuum service under the ASTM requirements for unalloyed oxygen-free copper. Each element is limited individually, because small amounts of antimony, arsenic, tellurium or phosphorus depress conductivity and can embrittle the metal at elevated temperature.
Size Range of Conductor Tubing
| Outside diameter, in (mm) | Wall thickness, in (mm) |
|---|---|
| 0.125 (3.18) | 0.032 (0.81) |
| 0.250 (6.35) | 0.032 (0.81) |
| 0.375 (9.53) | 0.065 (1.65) |
| 0.500 (12.70) | 0.065 (1.65) |
| 0.750 (19.05) | 0.065 (1.65) |
| 1.000 (25.40) | 0.125 (3.18) |
| 1.500 (38.10) | 0.125 (3.18) |
| 2.250 (57.15) | 0.125 (3.18) |
Sizes outside this table, other wall combinations, metric dimensions and custom cut lengths are produced to order, and tubing is supplied in straight lengths, in coils and with capped ends where bore cleanliness is critical.
Properties That Matter for Conductor Duty
High electrical conductivity, at the top of the copper range, so resistive loss in a given cross-section is at its lowest.
High thermal conductivity, which allows the conductor or envelope to shed heat quickly.
High ductility, so the tube can be bent, swaged, flared and formed without cracking, even in thin walls.
Good creep resistance at moderate temperature, which keeps joints tight in high-vacuum and pressurised assemblies.
Ease of welding and brazing, permitting vacuum-tight and pressure-tight construction.
Low relative volatility in a high vacuum, so the material does not contaminate the evacuated space.
No hydrogen embrittlement, because the oxygen content is too low to form steam at oxide inclusions during high-temperature reducing or brazing cycles.
Fabrication of Conductor and Vacuum Assemblies
Tube is normally ordered in the soft annealed condition for bending and forming operations and in a drawn temper where stiffness or dimensional stability is needed. Bending is done with internal support or with a mandrel to prevent flattening, and the bore is purged during brazing or welding to keep it clean and free from oxidation. Hydrogen-free atmospheres, or vacuum, should be specified for furnace operations. Where the assembly must hold vacuum, joint design should use proven sleeve, flange or graded seal geometry, and glass-to-metal seals are made with the copper in a fully annealed, scale-free condition.
Inspection and Documentation
Incoming material should be verified against the chemical limits above, with the analysis carried out on a representative sample, and conductivity confirmed by the resistance or eddy-current method. Dimensional checks cover outside diameter, wall thickness, concentricity, length and straightness, and the bore is inspected for cleanliness, scratches and embedded contamination. For pressure-containing assemblies, a hydrostatic or pneumatic proof test at the specified pressure is performed, and for electrical duty the certificate records conductivity, temper, dimensions and heat number. Tubes are supplied with protected ends and, where specified, sealed and purged so that the clean bore condition survives transport and storage.
FAQ
Q: What is C10100 OFHC copper tubing?
Seamless copper tubing made from oxygen-free high-conductivity copper with 99.99% minimum copper content and no residual oxide inclusions.
Q: How does OFHC differ from ordinary copper?
The oxygen level is below 0.0005%, so there are no oxide inclusions, conductivity is at the top of the copper range and the metal cannot suffer hydrogen embrittlement.
Q: What sizes are available?
Tubing is produced from about 1/8 in (3.18 mm) outside diameter upwards with matching wall thicknesses, and larger sizes, metric dimensions and custom lengths are made to order.
Q: What is the tubing used for?
Bus and hollow conductors, coaxial cable and coaxial tube, klystron and microwave tube components, wave guides, vacuum tube anodes, lead-in wire, cryogenic shunts and glass-to-metal seals.
Q: Can the tube be welded or brazed?
Yes. Tungsten inert gas welding, electron beam welding and furnace brazing in a protective atmosphere are all used, with the bore purged to avoid oxidation.
Q: Why is low volatility relevant?
In vacuum devices the material must not release vapour that would degrade the vacuum or deposit on sensitive surfaces, and oxygen-free copper keeps this loss extremely low.
Q: Which inspection is carried out before despatch?
Chemical analysis against the individual impurity limits, conductivity verification, dimensional inspection, bore cleanliness checks and, where specified, a pressure proof test.




