What ASME SB111 C70600 Tube Is
UNS C70600 is the 90/10 copper-nickel alloy - roughly nine parts copper to one part nickel, with deliberate iron and manganese additions. ASME SB111 is the ASME code adoption of ASTM B111/B111M for seamless copper and copper alloy condenser tubes and ferrule stock, and it is the specification most often called up for C70600 heat exchanger and condenser tube. The same alloy is covered by ASTM B466 for seamless pipe and tube, by ASTM B552 for desalting plant service, by ASTM B359 and B395 for finned and U-bend forms, and by ASTM B543 for welded tube.
Copper-nickel alloys form a protective corrosion product film that is rich in nickel and iron, and this film is what delivers long life in seawater. The iron addition is essential: it is the element that gives 90/10 cupronickel its resistance to erosion and impingement in flowing seawater, which is why the tube specification calls for a minimum iron content rather than only a maximum. A seamless wall, produced by extrusion and cold drawing, keeps wall thickness uniform in the hoop direction and avoids the weld line that would otherwise be the first place to corrode or crack under thermal cycling.
Chemical Composition and Mechanical Requirements
| Element | UNS C70600 tube (ASTM B111 / ASME SB111 limits) |
|---|---|
| Copper (Cu) | 88.6 % min |
| Nickel (Ni) | 9.0 - 11.0 % |
| Iron (Fe) | 1.0 - 1.8 % |
| Manganese (Mn) | 1.0 % max |
| Lead (Pb) | 0.05 % max |
| Zinc (Zn) | 1.0 % max |
| Property | Annealed (O61) seamless tube, typical certified values |
|---|---|
| Tensile strength | minimum about 275 MPa (40 ksi) required by the specification for the ordered temper |
| Yield strength, 0.2 % offset | minimum about 103 - 180 MPa, depending on temper and specification edition |
| Elongation | 30 % minimum in annealed temper |
| Density | about 8.94 g/cm³ |
| Thermal conductivity | approximately 40 W/(m·K), about one tenth that of pure copper |
| Maximum pressure-vessel service temperature | about 300 degrees C for the 90/10 grade |
Because thermal conductivity of a copper-nickel tube is much lower than that of pure copper, exchanger designers compensate with thinner walls and closer tube pitches. This is precisely why the annealed temper and a tightly controlled wall tolerance matter: every extra tenth of a millimetre of wall costs heat transfer.
Size Range, Tempers and Surface Finish
Outside diameter: commonly 6 mm to 300 mm, with 12.7 mm to 25.4 mm the standard condenser band.
Wall thickness: 0.5 mm to 10 mm; thin walls from 0.7 mm for low-pressure exchangers.
Length: straight lengths up to 12 m, or U-bent and coiled as required.
Temper: annealed O61 for expansion into tubesheets, with light-drawn tempers for higher strength where expansion is not required.
Finish: bright annealed, pickled, or polished, with clean ends and no drawing lubricant residue.
Forms: straight tube, U-bend tube, integral low-fin tube where surface area must be increased.
Seawater Corrosion Behaviour and Design Limits
90/10 copper-nickel resists uniform seawater attack, pitting, crevice corrosion and stress corrosion cracking, and the alloy is not susceptible to the dezincification that affects brasses. Its practical limits are set by velocity and by water quality rather than by basic material resistance.
Velocity: design water velocity is generally held in the range of about 1.5 to 3 m/s. Below that, deposits and biofouling build up; above it, erosion corrosion can begin, particularly at inlet ends and at bends.
Fouling: the alloy releases small amounts of copper ions that limit marine growth, which reduces cleaning frequency compared with steel and titanium.
Chlorination: continuous or intermittent chlorine dosing is compatible with copper-nickel, but over-chlorination and chlorine residuals combined with high velocity shorten life.
Sulphide: polluted or sulphide-bearing water can strip the protective film. Ferrous sulphate dosing and correct commissioning are used to rebuild it.
Ammonia: copper alloys including cupronickel are attacked by ammonia and ammonium compounds, so steam-side ammonia carry-over must be controlled.
Fabrication, Welding and Installation Guidance
Copper-nickel tubes are expanded into tubesheets in the same way as other condenser tubes, with wall reduction kept in the usual 3-5 % band to obtain a leak-tight joint without leaving excessive residual stress. Unlike brasses, 90/10 copper-nickel has good weldability: welded tube and welded pipe are available to ASTM B543 and ASTM B466 respectively, joints are made by gas tungsten arc and gas metal arc welding with matching copper-nickel filler, and repair of damaged tubes is practical.
Cut square and deburr both ends; a burr left on the tube end scores the tubesheet hole and creates a leak path.
Do not mix tube materials of different galvanic potential in one water box without evaluating the effect on the cathodic side.
Bending requires generous radii and, for tight radii, prior annealing; cold work followed by service in seawater increases susceptibility to stress corrosion cracking.
Keep tubes dry and capped during storage; standing seawater leaves chloride deposits that stain and pit the surface.
Confirm heat number, certified chemistry and mechanical properties on the material test certificate against the purchase order before installation.
Inspection and Quality Control Points
Eddy current examination of the full tube length is the primary seam and wall integrity check; hydrostatic testing is used where specified.
Dimensional inspection covers outside diameter, wall thickness, length, straightness and end squareness.
Chemistry verification by optical emission spectrometry on each heat, with nickel and iron both reported - iron below the minimum is a common cause of premature erosion failure.
Surface inspection for rolled-in scale, laps and deep scratches, any of which can initiate pitting in seawater.
Bundle marking and traceability so that in-service inspection results can be tied back to the manufacturing heat.
FAQ
Q: What is the difference between C70600 and C7060X?
Both are 90/10 copper-nickel. C7060X is the designation used for the enhanced grade with tighter limits on residual elements and a controlled iron range, and it is called up in specifications written for seawater piping systems.
Q: Why is iron specified as a range and not just a maximum?
Iron is what gives 90/10 cupronickel its resistance to erosion corrosion in flowing seawater. Too little iron leaves the protective film weak; the specification therefore sets a minimum as well as a maximum.
Q: Can C70600 tube be welded?
Yes. Copper-nickel alloys weld well by gas tungsten arc and gas metal arc processes with matching filler metal, and welded tube to ASTM B543 is available for applications where seamless tube is not required.
Q: What wall thickness should be ordered?
Wall thickness follows the exchanger design pressure plus a corrosion allowance and the tube expansion requirement. Thinner walls transfer heat better, so the selection is always a balance between mechanical margin and thermal performance.
Q: How does 90/10 compare with 70/30 copper-nickel?
The 90/10 alloy has higher thermal conductivity and lower cost and suits moderate velocities; 70/30 offers higher strength, better resistance in fast flowing and polluted seawater and higher allowable service temperature.
Q: Is C70600 tube suitable for desalination plants?
Yes. Copper-nickel tube is covered specifically for water desalting service by ASTM B552, and it is used in both thermal and membrane desalination installations.




