Sep 16, 2025 Leave a message

UNS-C44300-Admiralty-Brass-Tube.pdf

ASME B111 C44300 Admiralty Brass Seamless Tube for Heat Exchangers and Condensers

What C44300 Admiralty Brass Tube Is

C44300 is the arsenic-inhibited admiralty brass, one of the oldest and most widely used materials for condenser and heat-exchanger tube. It is a copper-zinc alloy with roughly 28 % zinc, about 1 % tin and a very small arsenic addition, supplied as seamless tube under ASME B111 / SB111 and ASTM B111.

The name admiralty brass comes from the naval service for which the alloy was developed: a tube that would survive continuous exposure to flowing seawater without the rapid dezincification that plain 70/30 brass suffers. Tin provides resistance to impingement attack and erosion-corrosion, while arsenic - present at only a few hundred parts per million - changes the electrochemical behaviour of the alloy so that it passivates rather than losing zinc. C44400 and C44500 achieve the same inhibition with antimony and phosphorus respectively.

Chemical Composition

The composition of C44300 is controlled to the following ranges by the product standard. Values are percentages by mass.

Element C44300 Function
Copper (Cu) 71.0–77.0 matrix
Tin (Sn) 0.9–1.2 resistance to impingement and erosion-corrosion
Arsenic (As) 0.02–0.06 inhibitor against dezincification
Lead (Pb) 0.07 max residual, kept low
Iron (Fe) 0.06 max residual, controlled
Zinc (Zn) remainder matrix balance
Other elements, total 0.50 max tramp element control

The narrow arsenic range is a specification requirement, not a manufacturing convenience: too little leaves the alloy open to dezincification and too much damages hot workability. Buyers should expect the mill certificate to report arsenic explicitly.

Mechanical Properties and Specification Requirements

The product standard sets minimum tensile strength, elongation and, for annealed tube, a maximum grain size for each alloy and temper. The applicable limits therefore depend on the temper ordered, and the acceptance test is a tensile specimen cut from the finished tube together with a grain-size evaluation on annealed material.

Annealed temper: the standard condition for tube that will be roller-expanded into a tube sheet or bent to a U-shape. Ductility is high and grain size is controlled to confirm complete recrystallisation.

Hard-drawn temper: higher tensile strength with lower elongation, used for straight rigid runs and where resistance to vibration is more important than formability.

Thermal conductivity: approximately 110 W/(m·K) at room temperature, which is lower than pure copper but sufficient for condenser duty and is one of the reasons the alloy is competitive with alternatives.

Pressure capability: the tube is used in shell-and-tube exchangers where the cooling water is under pressure; wall thickness is selected from the design pressure plus a corrosion allowance over the design life.

Every tube is normally inspected over its full length by eddy current after the final anneal, and a hydrostatic or pneumatic pressure test is performed when the purchase order calls for it.

Applications

Surface condensers: steam condensers in power generation, marine propulsion and process plants operating on clean or slightly polluted cooling water.

Shell-and-tube heat exchangers: coolers, heaters and interchangers where one side is water and the alloy can be matched to the less aggressive fluid.

HVAC and refrigeration: condensers, evaporators and cooling coils in packaged and industrial refrigeration plant.

Marine systems: lubricating oil coolers, jacket water coolers, air coolers and seawater heat-transfer components on vessels.

Power and process cooling: cooling towers, steam generators and auxiliary coolers where the water chemistry is within the alloy's design range.

Desalination and district cooling: condenser and cooler sections in plants where water chemistry and velocity suit an inhibited brass rather than a copper-nickel alloy.

Why Seamless Tube Matters in This Duty

Removing the weld seam removes the weakest link in a heat-transfer wall. A welded tube has a narrow band of cast, directionally solidified metal and a heat-affected zone alongside it; in a chloride-bearing water these regions differ in composition, residual stress and corrosion potential from the parent metal, and they are where pitting and cracking initiate. A seamless tube is homogeneous around its circumference, which produces uniform behaviour under roller expansion, thermal cycling and vibration, and it makes the eddy-current signal easier to interpret because there is no longitudinal discontinuity to mask small defects.

For the same reason the whole manufacturing route is directed at a uniform fine grain structure: casting, hot extrusion or piercing, cold drawing with inter-annealing, and a final anneal to the ordered temper. The tube that leaves the mill should be dimensionally concentric, because wall eccentricity thins one side of the wall during expansion and shortens the life of the joint.

Selection, Installation and Inspection Points

Match the alloy to the water. C44300 is right for clean and slightly polluted seawater at moderate velocity. Heavily polluted, sulphide-bearing or high-velocity water calls for aluminium brass such as C68700 or for a copper-nickel alloy.

Stay inside the design velocity. Low velocity allows deposits and under-deposit corrosion; excessive velocity removes the protective film and causes impingement attack.

Expand annealed tube only, and control the expansion so that the wall is not over-thinned at the ligament.

Stress-relieve U-bends to prevent stress-corrosion cracking in ammoniacal or chloride environments.

Exclude iron contamination. Carbon steel particles on the tube surface act as cathodes and start localised pitting; use non-ferrous tooling and clean storage.

Verify documentation: mill test certificate covering composition and mechanical properties, eddy-current report, dimensional record for outside diameter, wall thickness and ovality, and grain size for the annealed temper.

FAQ

Q: What does the arsenic in C44300 do?
It is a dezincification inhibitor. Added at 0.02 to 0.06 %, it modifies the surface film so that zinc is not selectively removed, which is what allows an inhibited admiralty brass to survive seawater service that would destroy uninhibited 70/30 brass.

Q: What is the difference between C44300, C44400 and C44500?
All three are admiralty brasses with the same copper, tin and zinc base, inhibited with arsenic, antimony and phosphorus respectively. The required inhibitor depends on the purchaser's water chemistry specification.

Q: Why is seamless tube specified for condensers?
Because the weld and heat-affected zone of a welded tube corrode and crack differently from the parent metal. Seamless tube has a uniform circumferential wall, giving predictable expansion and bending behaviour and a cleaner eddy-current inspection.

Q: What temper should be ordered?
Annealed tube for roller expansion into a tube sheet or for U-bending, and hard-drawn tube where rigid straight runs are required. The temper determines the tensile, elongation and grain-size limits that apply to the delivery.

Q: Can C44300 tube be replaced directly with a copper-nickel tube?
Not without checking the design. Copper-nickel has different thermal conductivity, strength and expansion characteristics, and the tube sheet, expansion procedure and water-box corrosion protection may all need review before substitution.

Q: How should the tube bundle be handled during a retube?
Keep the bore clean and dry, avoid carbon steel contact, expand to the specified torque or expansion rate, stress-relieve U-bends where required, and flush the bundle before returning the exchanger to service.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry