What C61400 Aluminium Bronze Is
C61400 is a wrought aluminium bronze, sometimes called aluminium bronze D. Copper is the base element, aluminium is present at roughly 6 to 8 % by mass, and iron at roughly 1.5 to 3.5 %. The alloy is not a brass and it is not a tin bronze: it is the aluminium that supplies the hard, adherent aluminium oxide film responsible for its corrosion resistance, and the iron that refines the grain and raises strength.
In practical terms C61400 sits in the middle of the aluminium bronze family. It is stronger and considerably more resistant to seawater than the copper-zinc brasses, while remaining easier to hot work and weld than the higher-aluminium alloys used for heavy wear duty. That balance is why it appears in pumps, valves, marine hardware and heat-exchanger water boxes rather than in coinage or electrical conductors.
Chemical Composition
The composition of C61400 is controlled within the following ranges in the ASTM wrought product standards. Values are percentages by mass.
| Element | C61400 | Effect |
|---|---|---|
| Copper (Cu) | remainder | matrix |
| Aluminium (Al) | 6.0–8.0 | strength, hardness, protective oxide film |
| Iron (Fe) | 1.5–3.5 | grain refinement, strength, resistance to impingement |
| Manganese (Mn) | 1.0 max | deoxidation and strength |
| Nickel (Ni) | 1.0 max | residual, controlled |
| Zinc (Zn) | 1.0 max | residual, controlled |
| Lead (Pb) | 0.01 max | kept very low for hot workability |
The low lead and low zinc limits are deliberate. Aluminium bronze is hot worked and welded, and residual lead and zinc both damage hot ductility at the working temperature, which is why this grade is specified with tight residuals rather than as a general-purpose bronze.
Mechanical Properties and Product Standards
Aluminium bronze is supplied in several product forms, and each form is covered by its own standard. Plate, sheet and strip are specified under ASTM B171 / B171M, bar and rod under ASTM B150 / B150M, and tube for heat-transfer duty under ASTM B111 / ASME SB111, which together define the permitted composition, the tempers available and the minimum tensile properties for each temper.
Strength and hardness: the mechanical properties quoted by any producer depend entirely on the temper supplied. The annealed condition gives the lowest strength with the highest ductility and is used where parts must be formed; the cold-worked tempers give substantially higher tensile strength, yield strength and hardness at reduced elongation. Always quote the temper, not just the grade.
Wear and bearing behaviour: the alloy has good resistance to adhesive and abrasive wear and is used for bushings, wear plates and slide surfaces running against steel, usually with grease or water lubrication.
Fatigue and impact: the combination of moderate proof stress and good toughness makes the grade suitable for pump impellers and valves exposed to pressure pulsation and occasional shock loading.
Thermal and electrical properties: like all copper alloys, aluminium bronze conducts heat and electricity well, but far less than pure copper; the alloy is selected for seawater duty rather than for conductivity.
Applications in Marine and Process Industry
Pumps: impellers, wear rings, casings and shaft sleeves for seawater, brine and slurry duty, where resistance to cavitation damage and impingement is required.
Valves and fittings: bodies, discs, seats and stems for seawater and process valves, and associated flanges and fittings.
Heat-exchanger water boxes and tube sheets: components that see the cooling-water side at high velocity and are therefore exposed to impingement attack.
Marine hardware: propeller shafts and sleeves, rudder and stern-tube components, fasteners, sea-water piping components and deck fittings.
Industrial equipment: wear plates, bushings, worm gears, slide bearings, welding torch tips and components exposed to dilute acids, alkalis and salt solutions.
Process plant: equipment handling non-oxidising acids and chloride-bearing solutions where the aluminium oxide film remains stable.
Corrosion Resistance and Service Limits
The aluminium oxide film that forms spontaneously on the surface is the source of the grade's reputation. It reforms rapidly if damaged, so the alloy tolerates the turbulence, cavitation and suspended solids that destroy the protective film on brasses. In seawater and in flowing brackish water it performs particularly well, and it is far more resistant to impingement and erosion-corrosion than admiralty brass.
The limits are equally well defined. Aluminium bronze is not suitable for strongly oxidising or strongly reducing acids, for solutions containing ammonia, or for high-temperature steam service, where the protective film is attacked or the alloy is embrittled. Where those media are present, the specification should move to a nickel-copper or copper-nickel alloy instead of pushing aluminium bronze outside its intended range.
Fabrication, Welding and Inspection Points
Hot working: the alloy is hot worked in the aluminium bronze range appropriate to the grade; overheating causes hot shortness, which is why the low-lead, low-zinc composition is mandatory.
Cold working: the grade cold works and forms well but work-hardens quickly, so multi-stage forming needs inter-annealing.
Machining: use sharp, positive-rake carbide tooling, heavy feeds and copious coolant, and take care to avoid the cutting-load rise that occurs as the tool dulls.
Welding: gas tungsten arc and gas metal arc welding both work; the filler should match the base alloy, the joint should be prepared and cleaned carefully, and preheat is used for thicker sections to avoid thermal cracking.
Inspection and purchase: confirm the grade and temper on the mill certificate, check the chemical analysis against the limits above, and require the mechanical test results for the temper ordered. For pressure-containing parts, add non-destructive examination as required by the design code.
Do not substitute by appearance. Aluminium bronze and manganese bronze are both yellow and are frequently confused, but manganese bronze is a high-strength brass and behaves quite differently in seawater, particularly under stress in the presence of ammonia.
FAQ
Q: Is C61400 a brass or a bronze?
It is a wrought aluminium bronze. Although the colour is similar to some brasses, its strength and seawater corrosion resistance come from aluminium and iron, not from zinc, and its fabrication behaviour follows the aluminium bronzes.
Q: What are the composition ranges of C61400?
Roughly 6.0 to 8.0 % aluminium and 1.5 to 3.5 % iron, with manganese, nickel, zinc each limited to 1.0 % maximum, lead limited to 0.01 % maximum and copper as the remainder.
Q: Which standards cover C61400?
Plate, sheet and strip are specified under ASTM B171 / B171M, bar and rod under ASTM B150 / B150M, and heat-transfer tube under ASTM B111 / ASME SB111. Each standard states the temper-dependent mechanical requirements.
Q: Why is C61400 preferred over admiralty brass for pump parts?
Because the aluminium oxide film survives turbulence, cavitation and suspended solids that strip the protective film from brass, so the alloy resists impingement and erosion-corrosion far better in fast-flowing seawater.
Q: Can C61400 be welded?
Yes. Gas tungsten arc and gas metal arc welding are both used with a matching filler, and thicker sections are preheated to reduce the risk of cracking. Clean joint preparation matters more than with steel because of the tenacious oxide film.
Q: In which environments should C61400 not be used?
Strongly oxidising or reducing acids, ammonia-bearing solutions and high-temperature steam service are outside its intended range; a copper-nickel alloy should be specified for those conditions.




